GSD3300V00CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Jamison, PA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
broken top roller rack
Took off the end cap- hardest part- took some twisting-be careful not to break it. After that slid out the old part and just popped the new one in. Then it took a little while again to put the end cap back in. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick J from Howell, NJ
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The rollers cracked and broke off the rack
Used a small flat head screw driver to remove the rail end covers (2) and removed the rack. Used my thumb to push the snap on roller assembly off the rack. The new rollers snap right back on the rack with just fing pressure. Re-installed the rack and then just pushed the rail end covers back on.
Very Simple Repair to a great machine. First problem in 13 years and still works great.
Very Simple Repair to a great machine. First problem in 13 years and still works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from Oxnard, CA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Top rack was collapsing because 2 of 4 support rollers were coming apart.
First, end caps were removed from support rails to free the washer rack. This is a little tricky - flexible rear finger of cap is bent back, then rotated inboard to permit end cap to slide out. Ten top wash rack is rolled out of washer. Old roller support assembies are pried loose and then snapped off their clamp locations on the upper wash rack, one at a time. Then the new rollers are snapped on in same way, except no tools are required.
Two of the old rack rollers were clearly worn out from nearly 10 years of normal operation, where plastic shaft is a bearing surface.
Two of the old rack rollers were clearly worn out from nearly 10 years of normal operation, where plastic shaft is a bearing surface.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gina from Mesquite, TX
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rollers on top rack were breaking
took the front pieces off the front of each bar and placed the new rollers in place. Put the front cover peices back. ....that's it! The only thing i used the screwdriver for was to help remove the pieces, one was more difficult than the other.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Belmont, CA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper rack kept falling down
Removed the rack.
Removed the roller bar.
Removed the roller base from the rack.
Removed the roller from the roller bar.
Replaced in reverse order.
DONE.
Removed the roller bar.
Removed the roller base from the rack.
Removed the roller from the roller bar.
Replaced in reverse order.
DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryll from Newville, PA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The top drawer of the dishwasher would extend past the support rails.
The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Davidson, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Cap had broken off the top rack, it kept sliding down
I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Gilbertsville, PA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
top rack roller separate from roller clip
had to bend back the metal tab that holds the end cap on. this is tricky and a poor design from a repair point of view. i finally got the end cap off without destroying it. replacing the broken wheel was very simple and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from EDEN PRAIRIE, MN
- Parts Used:
- WD28X31819
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rear 1/2" wheels on new rack were too narrow causing rack to fall off tracks
Removed 3/4" rear wheels from old damaged rack and installed them on new rack. Works fine now. For the price paid for this replacement rack, wide wheels should be included as part of the replacement package.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Simon from Spring, TX
- Parts Used:
- WD12X10327
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Upper rack rollers were broken
Removing the end caps on the rack's sliding arms was the hard part. It took some arm-wrestling and prying with a screwdriver to get them off. Replacing the rollers was a snap. Getting the end caps back on again was easier than removing them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from PLANO, TX
- Parts Used:
- WD28X31819
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Racked rusted out
Simply removed the old rack and installed the new rack.....easy as 123 ABC. Dishwasher still works fine but the bottom rack had rusted out. Not sure if this is common for this Hotpoint dishwasher as my deciding factor to order from here was that others had the same problem as me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from JONESBOROUGH, TN
- Parts Used:
- WD28X31819
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
NEEDED TO REPLACE LOWER RACK IN DISHWASHER TO SELL HOUSE
TOOK THE RACK OUT OF THE BOX AND PLACED IT IN THE DISHWASHER, DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martie from FULTON, MO
- Parts Used:
- WD12X10284
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Threads on the cap broken
A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SOUTHPORT, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap broke
Slide it into the arm until you hear it snap
Was this instruction helpful to you?
Thank you for voting!