GSD3300V00CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from UPPR CHICHSTR, PA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel had melted and support cracked
Removed the lower rack and installed new wheels with clips
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Asok from HELOTES, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Three of the 8 wheels broke.
The newly purchased wheels have a little different design and could be installed in a matter of few seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from LEVITTOWN, PA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water leak under Unit
Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Lithia, FL
- Parts Used:
- WD12X10264, WD02X10130
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rinse Agent Tank Leaks
The following steps were performed: 1) Disconnect power to the dishwasher 2) Unscrew all the screws on the inside of dishwasher door. 3) Remove outside plate on bottom of dishwasher. 4) Separate the dishwasher door after all screws are removed and pull out the old dishwasher rinse agent tank. There is a screw that needs to removed that holds the tank in place as well. 5) Snap in the new rinse agent tank and tighten screw in that holds tank in place. 6) Gently put the inside door back in place. Make sure all the holes line up correctly. 6) Put back the bottom plate of dishwasher. 7) Turn on the power again. You have now completed the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merle from Boulder, CO
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Severe lwater leak around door
Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from LAS VEGAS, NV
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Valve leaked
Turn off power and water from dishwasher. Remove Base Access Panel. Remove the upper 2 screws that holds the dishwasher in place. Pull out dishwasher. Locate the valve and remove the 2 screws holding the mounting bracket. (I used a hex Nutdriver to remove the screws) Remove the valve. Disconnect the wire connector. Disconnect water supply. (Place a towel to catch the water) Loosen the hose clamp holding the inlet hose and remove the hose. (I used pliers to loosen the clamp) Remove the elbow from the old valve and reattach to the new valve. (Use teflon tape around the threads) Reverse the Process. Check for leaks. Piece of Cake. Part was an exact fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Colleyville, TX
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher leaked
Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eduardo J from San Angelo, TX
- Parts Used:
- WD28X31820, WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rusted Racks
Replaced lower rack with new. Upper rack removed front stoppers, removed old rack, slit new rack in and replaced stoppers. Total time about 15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Carol Stream, IL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rinse Aid Fill Cap melted because it landed next to the heating element because it wasn't screwed in
Simply screwed in new cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bettie from ATLANTA, GA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper rack would fall down because of worn-out rollers
Determined not to call a repairman for such a simple problem, I watched your extremely helpful video. The ordered parts came right away and all it took was a screw driver and 30 minutes to take off and replace four rollers. So easy, this 75 year-old grandma could do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from SAINT LOUIS, MO
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
New home to me. Part lost
Put on a new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hillsborough, NC
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Put lower rack in
Took old rack out put new rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from PALERMO, ME
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing wheels
The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from THE VILLAGES, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels on the lower rack of our dishwasher kept falling off.
Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from BLUFFTON, SC
- Parts Used:
- WD35X21038, WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had cracked roller
Snapped right in
Was this instruction helpful to you?
Thank you for voting!