GLC4400R10BB General Electric Dishwasher - Instructions

When I first tried to fix the handle I could not figure out where the spring went. I went back online and looked at the diagram of the dishwasher on this site and learned where it went. Once I knew where every piece went it only took me about 5 minutes to put it back in and another 5 minutes to screw the cover back on. I am a newer homeowner and want to be able to do minor fixes. This was my first one and was very happy that I was able to do it on my own.

I replaced the broken/cracked soap and Jet Dry dispenser (i.e. MODULE RINSE AND CAP ASM - part #PS1481889). (Water was leaking into the soap holder and hardening the soap into a lump before the door would open, rendering the soad useless).

Steps:

1) Unplugged the dishwasher.
2) Unscrewed the 6 screws holding the front stainless steel panel to the plastic door; set aside panel and insulation.
3) Unplugged two wires from small electric motor in broken ASM.
4) Unscrewed 6 screws holding ASM in place; easily slid out of door.
5) Slid in replacement ASM and put 6 screws back in (tightened snugly to make slightly warped door bend to new ASM).
6) Plug back in two wires into new ASM.
7) Re-attached stainless steel cover to door (having a 2nd person hold this in place while screwing would've helped).

All done - works like a charm! No more dirty dishes because the soap didn't work right...

Bottom line: If you have a phillips head screwdriver, you can do this repair. Easy to do.

Installing the gasket took about 45 seconds. It actually took more time to scrub the area clean prior to installing. One quick trick I found was to fold the replacement gasket in two, and use that mark to center the gasket and press it in from there. That way you don't have any guesswork as to how much slack to allow for when starting.

Took screws out of door. Slid bottom seal off and slid new one on.

Everything snapped on quite easily. I was releaved to not have to replace "everything."

Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

Removed the wire clip, then removed two screws on mounting bracket. Then disconected the hose. Removed the brass elbow.

Then reversed these steps and I was done.

I took the front off of the dishwasher door, loosened the screws, unplugged the module and replaced it with the new module. This repair was the easiest repair I've ever completed!

Turn off water .Remove 4 screws holding lower front panels.Remove panels, valve is on left . Remove 2 screws that hold valve , slip valve up over clip. Using pliers slide clamp back, remove hose from valve.disconnect wire clip , unscrew from water fill line. Install new valve in the reverse order

Took off old funnel fill and put in funnel fill gasket and new funnel fill just to have a new one.

First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.

This isn't a terribly tricky repair, and the parts are cheap so it's worth a try!

(I had one tricky thing which was the door actuator broke while the door was shut. So I had to get the machine out of it's space without being able to open the front of the machine. I did this by lowering the feet in the front of the machine and then I used a hammer and flat chisel to break the two metal screws I had holding the top of the machine to the top of counter top...a little tricky!)

Remove screws from inside lower panel (where you put soap..the bottom) this will allow you to remove the inside of the door. But be careful as there are still wires attached so be careful to place the inside part without stressing the wires.

I needed to remove the metal harness and to open the black rectangular box that holds the interlock plunger so I could remove the plunger and spring (don't lose..and remember how it goes. take pictures if necessary). Then I was able to remove the broken actuator and see how it all fits together. It rests on top of the latch with notched side facing the inside of the machine. Make sure the notch is centered around where the interlock plunger is located.

Once you have the pieces fit together insert them into the door. Replace the plunger and spring and close the black rectangular box. Then replace the metal harness.

Hold everything in place and put the inside of the door back into position and lock it down with the screws.

You can test the door to make sure it's working but the whole mechanism is less functional when the machine isn't secured into its space. So, if you're mostly sure you've got it right, resecure the machine into its space making sure it's solid and then you should be good.

Like most everyone here I was very happy to accomplish this repair without calling in the repair service!! Awesome.

The first posted instruction is dead on (except there are 14 phillips screws (not 10) on inside of door. Also, when reconnecting the 2" quick connect, make sure it is fully inserted - otherwise the numbers on the display panel will not show correctly. Mine didn't the first time, and I had to re-open the door panel and giggle around with the connection to get the numbers to display properly.

My wife grabbed the upper rack as she fell backwards across the front of the open dishwasher. It broke her fall - she is fine thank goodness - but the roller slides broke and the rail was destroyed. The dishwasher repair was easy - just had to put new parts in place. The detail parts explosion helps in determining how all physically goes together. Everything works as good as new. I used the pliers to remove one of the old wheel axles that was attached to the basket.

Received part, removed lower panel and shut water and power off to appliance. Used flash light to see under dishwasher, removed the two screws that held part in place. Loosed clamp that held the water tube in place to part. Placed towel down to catch water. Pulled the line out so I could get to the nut that is attached to inlet part. Unhooked the plug after all water was gotten up. The main knuckle that's attached to the pump was on so tight that I took it to my local gas station for an mechanic to unscrew it for me....I have arthritis in my hands. Station is only two mins from me and wasn't a problem for them to do for me. Came back put fresh Teflon tape on joint and reattached it to new part. Attached all hoses and clamps, plugged electrical prongs back in and attached bracket back to body of dishwasher. Turned water on and checked for leaks. Turned power back on and ran a cycle of dishes to wash....all went well. If the knuckle was on so tight the job would have only taken about 40 min at best.