GSD2340V00SA General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ernest from Barrington, RI
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Parts needed for dish rack in my dish washer.
This is the second time I have order a part from this firm. They have been kind, helpful and sent my order to me immediately. The first part was a wheel for the dish rack in the dish washer. The second part was an end cap for the dish rack slide. I installed the parts within a minute. I am very pleased with their professional service and highly recommend them to anyone with an appliance problem where parts are needed quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M. from Phoenix, AZ
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
From the three bottom rack wheels on each side, the middle wheels were missing from each side.
I measured the diameter of the working wheels from the existing ones, and located the parts I needed from the website. I order two packages, each containing the wheels and axles for the rack.
When delivered, I snapped the wheels onto the delivered axles. Then, I snapped the axels unto the bottom rack, at the correct place. I used a large pliers for leverage because the axel was a bit tight to just simply snap on.
The middle wheels are located just behind the front wheels, thereby offering support when the botton rack is pulled forward for loading. Likewise, they offer support when the rack is pushed back in place.
When delivered, I snapped the wheels onto the delivered axles. Then, I snapped the axels unto the bottom rack, at the correct place. I used a large pliers for leverage because the axel was a bit tight to just simply snap on.
The middle wheels are located just behind the front wheels, thereby offering support when the botton rack is pulled forward for loading. Likewise, they offer support when the rack is pushed back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Finksburg, MD
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
GE Dishwasher leaking
Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERT from LYNN, MA
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Fill Cap broke off left portion in door
Used drill and easy out to remove broken part, then put in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from MADISONVILLE, LA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Had a water leak in bottom of dishwasher.
I simply removed the bad part and reversed the process. It was very easy and a 12 year old could do it. Thanks for the online tips and recommendations. You saved me over 400.00 which is what a new unit would run. Plus installation. Many Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robyn from Spring, TX
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the end cap for the top rack of the dishwasher broke
We simply followed the example of the end cap on the opposite side and snapped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Sarasota, FL
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my 78 year old aunt needed a bottom rack that was rusted and worn out
All she had to do was remove the old rack and replace with the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Arlington, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water leaking out from bottom of Dishwaser
Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Lake Elsinore, CA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rack end cap was missing.
I installed the end cap by pushing the new part on to the slide rack ,right rear side
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from mashpee, MA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom basket of dishwasher kept following out
i needed new rollers and inserts to keep wheels on now its like new when i pull out bottom basket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Fair Oaks Ranch, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom shelf would not roll properly
so easy! Ordered the rollers and clips ... popped them on and done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- R. Cecil from Norfolk, VA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheel was distorted
Simply replace wheel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Odenton, MD
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End Cap Broken
Removal of the old end cap required pliers. Not too difficult. The new end cap simply snapped into place. Both end caps on the two rack slides replaced in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Oak Hill, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
4 wheels missing from diswasher rack (lower)
removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelvin from Sun City West, AZ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaks
All new seals
Was this instruction helpful to you?
Thank you for voting!