GSD4060R15SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lawrence from Finksburg, MD
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
GE Dishwasher leaking
Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Houston, TX
- Parts Used:
- WD28X31820
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Removing the end caps on the tracks
I gently grasped the end caps with pliers and twisted them toward the center of the dishwasher while gently pulling on them. They came out with some minor difficulty. Be careful or they can be broken. When putting the caps back on the tracks grasp them with pliers to reinsert. Use a small srewdriver to assist in getting the plastic caps to slide into place. Wear light weight gloves when doing this to avoid getting cut on the sharp edges of the tracks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERT from LYNN, MA
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Fill Cap broke off left portion in door
Used drill and easy out to remove broken part, then put in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Sarasota, FL
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my 78 year old aunt needed a bottom rack that was rusted and worn out
All she had to do was remove the old rack and replace with the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robyn from Spring, TX
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the end cap for the top rack of the dishwasher broke
We simply followed the example of the end cap on the opposite side and snapped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Lake Elsinore, CA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rack end cap was missing.
I installed the end cap by pushing the new part on to the slide rack ,right rear side
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Arlington, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water leaking out from bottom of Dishwaser
Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Silver Spring, MD
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack end cap was lost or missing
All I had to do was slide the rack forward slightly, reach back to the end of the rack and snap the end cap into place. It helped to have someone there to balance the rack while I was replacing the cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelvin from Sun City West, AZ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaks
All new seals
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from The Villages, FL
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cap broke
The end cap took about 2 minutes to replace. I received my part quickly and installed it really quick and easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Odenton, MD
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End Cap Broken
Removal of the old end cap required pliers. Not too difficult. The new end cap simply snapped into place. Both end caps on the two rack slides replaced in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Oak Hill, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
4 wheels missing from diswasher rack (lower)
removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Chatham, NJ
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Discovered that the end caps were broken
Removed the broken items and clicked the new ones in place utilizing a pliers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from Claremore, OK
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The end cap broke off so when we would pull out the upper rack the whell would fall off of the track.
The end cap snapped into place perfectly without any problems and the rack works like new again. This is the second time I have used PartSelect.com and I am very satisfied with how fast I recieve the product and the easy of finding what I need. I would recommend them to anyone!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hampton, GA
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door had no resistance/no balance/would fall open
First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!
Was this instruction helpful to you?
Thank you for voting!