GSD3300V00WW General Electric Dishwasher - Instructions

I followed the video instructions on removing the rack slide end cap to prevent breaking it and it was very easy to remove and replace the broken one. I attached the new rack rollers and voila we were back in business. I was about to order a new dishwasher the night before for $5oo! Thankfully the stores website wasn't working so I couldn't. I decided to look online to find out if it was easy just to replace the parts. Looks like I saved close to $500 just replacing those parts! AWESOME!!!!!Thank you for a user friendly website. It made all the difference")

removed the end caps and took the rack out of the dish washer.

found right front rack roller bad and replaced.

slide rack back into dishwasher and replace end caps.

Removed the white end of the top track. Pulled off the remnants of the rack roller. Slide the rack roller wheel into the track and popped the other end on the top rack (looked at the other rack rollers to see how it fit.) After that, I put the end back on the track.... Note what is the top and what is the bottom of the track end. Realizing that there is a wider area on the track to slide part of the white track end through to get it on without much effort.

There is nothing worse than having a knob break off when using the dishwasher. The great thing is that I was able to go on the internet and found your supply outfit. I ordered the replacement and had it to install in less than 48 hours. The knob was the right one and now I use the dishwasher again TNX

Very easy, just twist the back 1/2 of the white tab that is in the end of the roller bar and pull out the front. Be sure to put back in the opposite when finished

Removed the plastic end cap on each roller guide , snapped off the existing four rollers and removed. Inserted the new rollers into the guide, secured them into their places and replaced the end caps.

I watched the Part Select video, and it was very helpfull.
But next time I would watch the video before I ordered the parts, and think about other parts that I may break duing the repair.

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

Took off the end cap- hardest part- took some twisting-be careful not to break it. After that slid out the old part and just popped the new one in. Then it took a little while again to put the end cap back in. No tools needed.

Removed the rack.
Removed the roller bar.
Removed the roller base from the rack.
Removed the roller from the roller bar.
Replaced in reverse order.

DONE.

had to bend back the metal tab that holds the end cap on. this is tricky and a poor design from a repair point of view. i finally got the end cap off without destroying it. replacing the broken wheel was very simple and easy.

Used a small flat head screw driver to remove the rail end covers (2) and removed the rack. Used my thumb to push the snap on roller assembly off the rack. The new rollers snap right back on the rack with just fing pressure. Re-installed the rack and then just pushed the rail end covers back on.

Very Simple Repair to a great machine. First problem in 13 years and still works great.

I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.

took the front pieces off the front of each bar and placed the new rollers in place. Put the front cover peices back. ....that's it! The only thing i used the screwdriver for was to help remove the pieces, one was more difficult than the other.

Fiddled with the rollers until figuring out how to remove them. Hardest part was getting the stops off the ends of the roller guides. Replaced rollers, replaced rack, replaced ends of roller guides. Voila