GLD6906R30WW General Electric Dishwasher - Instructions

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!

My wife grabbed the upper rack as she fell backwards across the front of the open dishwasher. It broke her fall - she is fine thank goodness - but the roller slides broke and the rail was destroyed. The dishwasher repair was easy - just had to put new parts in place. The detail parts explosion helps in determining how all physically goes together. Everything works as good as new. I used the pliers to remove one of the old wheel axles that was attached to the basket.

Ordered the new parts and attached to wheels on lower rack. The old pieces clamped on and the plastic stretched out and would not hold any longer. The 8 new pieces have a slightly different design, were easy to intall and I believe will never loosen up.

This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.

This repair was a snap. The parts, though not identical to the original, fit perfectly. I was able to snap both the Rack Slide Cap and the new wheel axle to the existing washer cage and the machine works great now.

Thanks for the quick delivery and great website!

Ordered drain pump kit (GE part # 325). When it came it looked different from the pictures in the manual and what was ordered. Thought I was going to have to retrofit pump. Looked at ordering a drain kit from another source, which I did. When that came it was exactly the same as the one I ordered from Part Select. I returned the other pump.
Looking at the parts diagram, I discovered the replacement pump (part # 325 ordered) was combined with part # 327 which is why it looked different. I went ahead with the replacement, pulling out the pump and the connecting tubing, part # 327. The replacement pump fit exactly in place, replacing the pump and tubing. I put the dishwashing machine back together and it works great.
Bench tested the old pump and it worked. It must have had a food ball caught in the impeller, inhibiting flow. Next time I'll check all the parts for grease and food balls before ordering new parts..

Per ps video. Really easy. Disconnect power, Remove front lower panel, remove Power leads, 2 installation bolts, remove 2 spring clamps on feed/exit hoses,reinstall.

The sump was very clogged with caulk like crud that we think was a chemical reaction from soap that was used the first two years. When I first started troubleshooting, the sump seemed to be the problem, so I replaced that. There was a small hose on the sump that was broken so it made sense to replace it anyhow.

When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.

I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.

Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.

My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.

TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.

Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.

Got the part the next day.. opened it and just screwed into place!
Easy as could be. Thank you!!

The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.

Opened the door on dishwasher and installed the rinse aid cap. Checked for leaks. None found

opened the box , new one was an exact fit, pulled out the old one and dropped the new one in place??, this is more of a review, the new part was the exact same one...perfect!

Great