Models > GFLD560N10SS > Instructions

GFLD560N10SS General Electric Dishwasher - Instructions

Jump to:

All Instructions for the GFLD560N10SS
106 - 120 of 387
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Gail from Woodstock, GA
Parts Used:
WD12X10278
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
axle for wheel was broken
Popped the axle on to the wheel, then snapped it on to the lower drawer - done!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kimberly from Durango, CO
Parts Used:
WD12X10278, WD35X21038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
some wheels had broken, was really hard to move rack in and out.
I am NOT handy, but my husband was gone when the wheels and stud/axles came. I was able to replace all of them in about ten minutes with no tools. Easy and no more frustrations!!!!!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alfred from Mashpee, MA
Parts Used:
WD12X10278, WD35X21038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
the lower rack wheels had fallen off and melted
The best money I've spent on a repair. Easy. The lower rack now rolls in and out smoothly.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from Maurice, LA
Parts Used:
WD22X10084, WD22X10047, WD22X10046, WD12X10109
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
dishes where not clean after washing
change the nozzles and filter
7 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Hudson, FL
Parts Used:
WD21X10247
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
main control board malfunction
Diassembled the door from the insside and installed new board as instructions specified.
Frustration is that this is the second time I have had to replace for the same dishwasher....
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kathleen from LOUISVILLE, KY
Parts Used:
WD28X10384
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
dishrack was worn and causing chips on dishes
just slid the new rack into place
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michelle from Carlisle, PA
Parts Used:
WD12X10163
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Detergent cap would not stay closed
After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chester from North Las Vegas, NV
Parts Used:
WD28X10399
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
Top rack had the plastic coating coming off
Had to replace the top rack in the dishwasher. Removing the top rack was a tricky. Have to push the tab out not in on the stopper ends of the rack. Unscrew the bolts on the water sprayer. Need to slide the sprayer instead of unclipping it. Real easy to do once it is realized. Should have taken 30 minutes if I knew this in advance
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
KEVIN from MACKINAW, IL
Parts Used:
WD12X10163
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The detergent dispenser latch was broken
The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edwin from Waldwick, NJ
Parts Used:
WD12X10278, WD35X21038
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Wheels kept falling off
Removed the old wheels and studs. Pressed on the new studs and wheels. Viola.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eric from SIMPSONVILLE, SC
Parts Used:
WD12X10163
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
The door on dishwasher soap dispenser broke.
Repaired the soap dispenser.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Dublin, OH
Parts Used:
WD12X10163
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Old soap dispensor latch would not hold
Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Everett from FREDERICKSBRG, VA
Parts Used:
WD15X10003
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
No water in
Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ARTHUR from OAK PARK, IL
Parts Used:
WD12X10163
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers
Detergent dispenser did not work
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOHN D. from GOSHEN, IN
Parts Used:
WD01X10175
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
wouldn't drain
Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GFLD560N10SS
106 - 120 of 387