GHDF360R10SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from KENT, WA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
valve leaked
shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from BRIDGEPORT, WA
- Parts Used:
- WD21X10169
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher was stopping mid-cycle and beeping every 15 seconds (as if the door had been opened)
I watched this video: https://www.youtube.com/watch?v=-k0iZGwMOGc
And then I did exactly what it said! It was easy. Plus, when I opened the panel I could see the old switch interlock assembly was melted on one side, so I knew I had gotten the right part!
And then I did exactly what it said! It was easy. Plus, when I opened the panel I could see the old switch interlock assembly was melted on one side, so I knew I had gotten the right part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from DALLAS, TX
- Parts Used:
- WD01X10393, WD14X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Plastic coupling broke on door cable counter balance
Removed dishwasher from under counter. Removed both cable pulleys and bushings. Threaded new cables and remounted pulleys and bushings. Finally stretched springs onto cables. Checked counter balance and reinstalled dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ARTHUR from OAK PARK, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Detergent dispenser did not work
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from RICHMOND, TX
- Parts Used:
- WD19X10039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Dishwasher would not drain
Replaced impeller
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- curt from sandy lake, PA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The clip that holds the soap dispenser shut broke.
Took screws out that hold front panel on, unplugged wiring, changed soap dispenser, and put everything back together. Not a bad repair at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from MADISONVILLE, LA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Had a water leak in bottom of dishwasher.
I simply removed the bad part and reversed the process. It was very easy and a 12 year old could do it. Thanks for the online tips and recommendations. You saved me over 400.00 which is what a new unit would run. Plus installation. Many Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from WYNNEWOOD, PA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack was bent, didn't like rolling out of the dishwasher anymore
I removed the old rack and saved the flatware container. Then I put the new rack in.
The difference between the old one and the new one is that between a busted grocery cart with one wheel that always wants to return to the parking lot, and a well-trained dog that does exactly what I ask it to. The new rack was worth the $95 I spent to get it.
The new rack came with wheels and axles, so I didn't need to order more.
The difference between the old one and the new one is that between a busted grocery cart with one wheel that always wants to return to the parking lot, and a well-trained dog that does exactly what I ask it to. The new rack was worth the $95 I spent to get it.
The new rack came with wheels and axles, so I didn't need to order more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Delanco, NJ
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
detergent cup latch broke
Very easy - remove the screws around the inside of the door. 6 screws and 2 plugs to remove the assembly. Just be careful not the strip the sheetmetal screws when putting it back together. No screwguns...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Isabel from Louisville, KY
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom rack was rusted out
I took out the old rack and rolled in the new. I thought I was going to have to take the rollers off the old one and put them on the new, but they were already on the new rack. The hardest part was getting into the box. I am an 80 year old female.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Smithtown, NY
- Parts Used:
- WD35X21041, WD02X10106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Tray rollers had broken off.
Replaced the original roller connectors with newly designed connectors. Works much better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Bloomingdale, GA
- Parts Used:
- WD24X10045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Missing drain hose
Simple as 1,2,3.Parts on time and priced right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Venice, FL
- Parts Used:
- WD24X10045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Recived used without drain hose
It was an install. My problem is that the drain tube is not standard to other dishwashers,so I could not get it at either of the local home improvement centers. The good news is that it is larger than the standard, and offers better discharge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucille from North Babylon, NY
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom rack had bad design on wheels and kept falling off making the dishwasher unuseable
I ordered wheels on this wonderful site that looked like they made more sense and replaced all eight on my dishwasher and FINALLY the dishwasher isn't the nightmare it has been. It took seconds to pop in the clip to the roller and pop it on the rack. Thank you PartsSelect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Denver, CO
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheel studs were worn out, glide arm stopper part gone, needed wheels for upper level tray
Very easy, saw the parts I needed online, ordered them, and installed them. Easier than I thought. Saved probably $200 in having a repair man come to the house. Outstanding results! Thank you!
Was this instruction helpful to you?
Thank you for voting!