GLD6964R30SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Diana from NAPLES, FL
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old silverware basket wore through and melamine utensils fell through and stuck to heating element which cost me $100 for repairman to remove
Put new basket in, threw old one away
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from royal oak, MI
- Parts Used:
- WD12X10401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
a couple of retaining ears were broken from the cover allowing the the switches and plunger to move out of place
took screws from inside door panel and replaced the cover taking care not to allow plunger and spring to pop out put panel in place and screwed down
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laverne from Roselle, IL
- Parts Used:
- WD12X10278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pieces that attach the wheels to the lower rack kept falling off
Ordered the new parts and attached to wheels on lower rack. The old pieces clamped on and the plastic stretched out and would not hold any longer. The 8 new pieces have a slightly different design, were easy to intall and I believe will never loosen up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Fitchburg, WI
- Parts Used:
- WD12X10304, WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
End Cap and Wheel axle were worn or broken
This repair was a snap. The parts, though not identical to the original, fit perfectly. I was able to snap both the Rack Slide Cap and the new wheel axle to the existing washer cage and the machine works great now.
Thanks for the quick delivery and great website!
Thanks for the quick delivery and great website!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MarilynNegri from BLAIRSTOWN, NJ
- Parts Used:
- WD12X10206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost cap to rinse aid disoenser
Just screwed it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from DEERFIELD, IL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
One axle cracked and broke off; another wheel was had fallen off and was distorted when it hit the heating element.
Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helmut from EAST KINGSTON, NH
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower wheels kept falling off
Installed new lower rack wheel kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from PALMER, MA
- Parts Used:
- WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers and axles were worn out
Removed the stops at the end of the upper rack, removed the old rollers. Replaced with new rollers and installed the stops back in place. Very easy, finished in less than 15 minutes. Replacement rollers very much improved with design from the original rollers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John C from SPRINGFIELD, VA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bottom dishwasher rack rusted out
Simple install- just roll it in. Fit perfect. Better design than OEM part. Perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alton from HARTWELL, GA
- Parts Used:
- WD28X10128
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Silverware basket
Took old basket out and dropped new one in .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ANNAPOLIS, MD
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Leaking Solenoid valve
1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from HGHLNDS RANCH, CO
- Parts Used:
- WD15X10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Dishes Weren't Getting Clean At All
The sump was very clogged with caulk like crud that we think was a chemical reaction from soap that was used the first two years. When I first started troubleshooting, the sump seemed to be the problem, so I replaced that. There was a small hose on the sump that was broken so it made sense to replace it anyhow.
When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.
I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.
Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.
My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.
TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.
When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.
I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.
Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.
My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.
TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from GLEN ALLEN, VA
- Parts Used:
- WD05X10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Dishes were not drying inside the dishwasher after the dishwasher cycle completed
The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from HAYMARKET, VA
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Leaked front right side
Followed the instructions that came with the my order
Was this instruction helpful to you?
Thank you for voting!