GHDT108V00BB General Electric Dishwasher - Instructions

It was very simple to install. At first my husband thought I had ordered the wrong part. I guess they just revamped the part and it worked out really well. And I didn't have it mailed special but I got the parts in about 2 days. My only problem is that the shipping cost as much as the parts.
But the parts are installed and the wheels don't fall off anymore!! If I need anything else I will use your company again and I will tell friends and family about you guys.
Thanks

I only had to repair the wheel axle. Since I read another post stating you don't have to change the wheels, I ordered only the axle and they popped right into the existing wheel and attached to bottom rack better than original design.

The replacement studs that were suggested fixed the problem that we were having. The fix was easy and took less than ten minutes to take the broken studs out and snap the new ones into place. The studs are designed to hold onto the rack much tighter than the original studs and completely fixed the problem of the wheels falling off anytime you tried to move the bottom rack.

I inserted wheel axle into wheel and attached to bottom rack axle. It was simple. No problems.

I examined the wheels and noticed that they were actually fine, it was just the clip on axles that had worn out. I had recently used a dishwasher cleaner, I think that was the straw that broke the camels back. The replacement axles that I ordered were actually a bit different than the original. It turns out they had been greatly improved, so the new ones snapped easily into place by hand. The lower rack rolls perfectly, like new!

The repair was so simple a child could do it. It took less than five minutes and now the drawer rolls smoothly and is quite sturdy.

Used plier to pinch the axle head to take the old wheels off then pushed the new wheels on by hand.

Remove all wheels on one side. Use pliers to remove broken axles from wheels. Pop in new axles, then go to lower rack and attach to rack by pushing axle pinch mechanism onto rack support. New axles do not look like old ones—they are improved.

We ordered 4 wheels and axels, took off the old wheels, assembled the new wheels by popping the axel into the wheel (really simple) and then snapping them onto the post. It was incredibly simple. We waited 3 days for the wheels to arrive,the mailing cost was more than the parts! The result is amazing, the lower rack now runs smoothly and sits inside the washer as it should do without falling down all the time. Well worth the small amount of effort to find the right part and much cheaper than buying a new one!

Ordered on a Friday and parts arrived Sat. No tools required. Pieces easily slipped into place. Dishwasher is all fixed. This site is much easier to use than GE's. Will use PartSelect for all future replacement parts.

So easy and the posts on the site were incredibly helpful in determing what part i needed. The wheels on the dish rack inside the dishwasher kept falling off. I had to keep lifting the dish rack in and out of the dish washer to load and unload it. Unbelievably annoying. I popped the old wheel axels out of the exisiting wheels and replaced them with the new wheel axels I ordered from PartSelect. Then I attached the wheels back on the dish rack and it was right back to normal.

Very easy job. Just took out the bottom rack and replaced the wheels that kept falling off. A no brainer! works wonderful now. Most impressed with the ease of ordering and amazed how quickly the parts were delivered to me. I saved alot of money doing it myself! Thnak you

old axles were removed by pulling wheel assembly from lower basket pins. squeezed old axle with needle nose pliers and discarded broken wheel axle. snapped wheels in place on new wheel axle and snapped wheel assembly into place on the basket. i replaced only two axles since the remaining ones were still intact. actual repair time was under three minutes. if all eight wheels would have to be replaced, i'm positive it would have taken no more than five to six minutes. in fact, the new wheel axle is a much better design than the original.

I first tried the local appliance shop i got the wrong parts twice. I then wrote the model and serial #'s of my unit and found parts select. Got the right parts quickly and all I had to do was pull the old rack out and slide the new one in. Viola she was done ! Thanks Part Select !
Matt Hansen

Only one axle was broken, but I replaced all 8 because GE had redesigned the axle to prevent future problems. Decided to just replace them all and be done with it. Took 10 minutes, start to finish and all is well.