GLD2850T05CS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from Waterville, ME
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M Anne from VIENNA, VA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Our dishwasher lower arm had become clogged
HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from LAKE WALES, FL
- Parts Used:
- WD08X10059
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom door seal had crumbled with age
Removed inside of door, slide bottom seal on and put inside door back on. Job done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack D from CLEBURNE, TX
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heat shield on lower spray arm came loose and blocked spray arm from turning
Followed instructions on how-to video on website on how to remove and replace lower spray arm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryll from Newville, PA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The top drawer of the dishwasher would extend past the support rails.
The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from AVON, IN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Mainly leaking Rince Aid, but occasionally the soap door did not open to dispense soap
Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SIMPSONVILLE, SC
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The door on dishwasher soap dispenser broke.
Repaired the soap dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Davidson, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Cap had broken off the top rack, it kept sliding down
I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carla from valdosta, GA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Food particles had started stopping up spray arm and get them out.
Pulled old spray arm off and snapped new one on. Less than 3 minutes and works great. Dishes are cleaner now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- curt from sandy lake, PA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The clip that holds the soap dispenser shut broke.
Took screws out that hold front panel on, unplugged wiring, changed soap dispenser, and put everything back together. Not a bad repair at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from O BRIEN, FL
- Parts Used:
- WD12X10304, WD02X10169, WD12X10197
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Middle spray arm not turning
One of the rack slide end caps broke so only one end cap kept the rack from falling out. The video guide worked for me to remove the remaining end cap allowing the rack to come out. I then replaced the middle arm conduit carrier as it no longer had a tight fit. I then replaced the middle spray arm bearing and reinstalled the rack and the rack slide end caps using the video supplied online by this site . Ran dishwasher and verified middle spray arm was turning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- hugh from upper marlboro, MD
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
machine would not fill (with water)
Checked availability of replacement machine and replacement parts online..in this process, I ran across a similar story by someone who fixed similar problem on a similar machine. Before removing the fill valve, I tried to confirm that it was defective my reading solenoid coil continuity. It looked ok so I could not use that info to confirm a bad fill valve, although that possibility was not eliminated. So I ordered a replacement fill valve, removed existing fill valve and took a long position on paper plates. On delivery of the valve, I found that its mounting bracket (which forms a part of the supply pressure boundary) had been redesigned to conform to a year-2000 redesign of the machine. Valve instructions allowed for this and provide for retention of mounting bracket from old valve for use on new valve. Instructions indicated the o ring from new valve (vs old) should be used in attaching the old bracket. I found that the o ring groove in the new valve was so deep that o-ring compression on reassembly was prevented. I went ahead and put together with new o-ring. When turned on supply pressure, it began leaking immediately, so I shut down, removed valve again. During this (2nd) reassembly, I stacked both o rings in same groove in order to get compression at all. Reinstalled valve w/ both o rings....no leaks and it works. I think valve design should be reviewed and depth of o ring groove reduced so only one o ring is needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Pagosa Springs, CO
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench set
Water inlet valve was leaking due to crack
After removing the front panels, I removed two screws holding the valve in place. I turned off the water supply and removed the water line, unclipped the hose clamps and took the faulty valve out. I then reversed the above steps and turned the water back on. NO leak. Very easy to do andthe repair took ~20 minutes to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Sissonville, WV
- Parts Used:
- WD22X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm broke
Replaced lower spray arm
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Lehigh Acres, FL
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tack was missing endcap causing rack to fall when pulled forward
Press endcap in place after ensuring the rack is in track
Was this instruction helpful to you?
Thank you for voting!