GLD3806T05BB General Electric Dishwasher - Instructions

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

took screws from inside door panel and replaced the cover taking care not to allow plunger and spring to pop out put panel in place and screwed down

Three of the four roller of my upper shelf of my dishwasher had broken...I went on line and in ten minutes ordered my rollers....a few days later rollers came and within fifteen minutes my dishwasher was up and running.....thank you so much....I will absolutely use this site again for future repairs....Thanks again. Marlene Martin

Had to pull the dishwasher from under the counter to access the water inlet valve. Disconnected the hoses from the inlet assembly. Removed the inlet assembly from the dishwasher frame. Installed the new assembly and reconnected the hoses. Plugged the dishwasher in, selected a cycle to run to check for leaks.

Hired my neighbor, who is a plumber.

Followed the instructions that came with the my order

The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.

changed the door gasket no tools,just pulled out the old,lined up the dot (printed on gasket)on the new and started at the top pushed in the new took five minute,the short bottom door seal required a phillips head screwdriver to remove the inside door screws(six screws) the two on the bottom are different they attach to the door hinge and are machine thread the other four are coarse thread.lifted off the panel slide off the old(pay attention to which way the curve goes) slide on the new replaced the panel put in the six screws.the job is done! the door will be tight to close but will be easier after a few uses.

I first watched a video on trouble shooting on You Tube. I took the insides of the dishwasher apart and found broken glass and some other debris.I shop vacuumed the inside and the dishwasher pump put back together and ran a rinse cycle,unfortunatly dishwasher was not draining. Got the model number and ordered the dishwasher pump through Part select. Within in a few days I had the part in hand and had to remove the dishwasher from under counter. Once turned over the pump was right there ands took 5 minutes to change replaced pump put everything back together and now dishwasher drains as expected.

Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.

Unscrewed the screw holding it in place and removed it, out the new one in place and screwed it on. Very quick and simple.

I removed top dishwasher rack, popped off broken studs, and removed wheels from the tracks. I replaced studs on rack by popping them into place, and I slid new wheels back into wheel tracks. I place new studs into wheel assembly, slid rack back into dishwasher and replaced stoppers at the front of the tracks.

I removed the old gasket very easily as there wasn't even glue holding it in place. The new gasket just pressed right into a slot and makes a water tight seal.

Ordered the new parts and attached to wheels on lower rack. The old pieces clamped on and the plastic stretched out and would not hold any longer. The 8 new pieces have a slightly different design, were easy to intall and I believe will never loosen up.

This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.