GLD2850T10CS General Electric Dishwasher - Instructions

simply removed broken valve and replaced with new valve, easy peasy. shipping was GREAT, Overnight. all in all a easy fix.

look at neww part first then r&r

Remove the eight door screws. Pull plastic inner door panle off. Disconnect wires for the detergent door opener (mark them first). Clean inside the door and the seal area on the washer. Slide out bad seal, slide new one in. Reinstall. I went to home depot and replaced the rusting screws with stainless screws.

Removed the old axle locks and replaced with the new ones. They work fine. They had impoved the wheel lock over the original ones. Thanks for the good & quick service.

removed old parts and installed new without any problems.

pulled switches flicked leaver worked when itwanted to and not every time. I removed then shorted then rechecked everthing worked. got on line ordered parts good price fast service fixed 30 min when they came in saved money.Thank God! 20.00 fix instead of 200.00 +

My wife said the door broke; we need a new dishwasher. It is not worth a $100 repair out of warranty. I checked this site the springs were about $4 each. When they arrived I unscrewed two screws holding the dishwasher to the counter; carefully pulled the dishwasher out from under the counter; found the broken spring replaced it and for good measure I also replaced the old working spring on the other side. The door now works fine. Total time less than a half an hour.

After reading other customer responses I decided to attempt the repair myself. After pulling out dishwasher I turned it on it's side and prodeeded to remove the 3 screws holding it in place. FIFTEEN minutes later I pushed it back into position and it has performed like new for the past month. Comparing parts and service I saved about $200.00 on this self repair. I would not hesitate to undertake another repair after my experience.

im 73 years old and a lady did it myself very easy

I unscrewed all the screws from the inside of the dishwaher door. I took out the broken part, installed the new parts and screwed the screws back in. Part Select was wonderful to work with and the parts arrived the day after they were ordered.

Removed the holding screws around the edges; removed and replaced the soap container; reconnected the electrical leads, and done... Very simple fix. But it does get a little tricky since the door is spring loaded. NOTE: THERE ARE SCREWS AT THE BOTTOM THAT IS NOT OBVIOUS.

Easily screwed on this part and used it for the door of the dishwasher to properly open and close

I unscrewed the screws in the door of the dishwasher. Then pulled the inside part of the door up and unscrewed the 6 screws that held the dispenser. I am not sure the correct name of the part but it is on the backside of the dispenser and is red and it is where the wires connect to it, that was probably the most difficult part, disconnecting the plastic covers from the old dispenser. I used a butter knife to pop it out and then was able to get a better grip to pull them off. I pushed the wires on the new red thing and then put the new dispenser in place. You have to make sure that the dispenser is in the right spot and the brace on the underside of the inside part of the door, is in the correct place, otherwise, you will have a leak. Which is what happened to me. I just unscrewed and opened it again and screwed the screws tighter and it was fine.

Open the door and go along entire edge of door and use Philipps to unscrew the front panel of the door from the inside panel of the door. Once unscrewed open carefully. There are screws in the dispenser cup. Undo those and then there are two plugs to be undone. There is also the main black computer component that has to be unplugged from its cord. Just remove and screw everything back the way it was. This was my first time and I am a female age 58 years old. It was simple. If I had to do it again I could do it in less than half the time.

1. Pulled the dishwasher out. 2. Removed old element fasteners and leads. 3. Installed new element and reattached fasteners and leads. 4. Pushed back in. Very simple. More work getting the dishwasher out to be able to access than actually replacing the part. The dishwasher is running great again and saved me at least 100 dollars for a service call. . Your service was just outstanding. Received multiple emails on status of shipment and a nice video for replacing. Just outstanding customer service from Part Select.