GLD2850T10CS General Electric Dishwasher - Instructions

I first watched a video on trouble shooting on You Tube. I took the insides of the dishwasher apart and found broken glass and some other debris.I shop vacuumed the inside and the dishwasher pump put back together and ran a rinse cycle,unfortunatly dishwasher was not draining. Got the model number and ordered the dishwasher pump through Part select. Within in a few days I had the part in hand and had to remove the dishwasher from under counter. Once turned over the pump was right there ands took 5 minutes to change replaced pump put everything back together and now dishwasher drains as expected.

I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!

The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.

Popped the axle on to the wheel, then snapped it on to the lower drawer - done!

After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.

two screws, two minutes, all done

placed the end cap into location and forced it into place. Fixed -and we are all much happier!!

No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!

I removed the plastic end caps by gently pushing and twisting them. Once the end caps were off the basket slid out. The old wheels were removed and the new ones clipped in very easily. I then slid the basket back into place and replaced the end caps. The most difficult part was removing the end caps. I was afraid that I would break them, but by being careful and not forcing the piece they easily came off.

I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

Removed inside of door, slide bottom seal on and put inside door back on. Job done!

I called your tech and she sent me a awesome video that made it so easy to fix on my own

Easy install, snap in new axle and put wheel on stud. Be sure to check all wheels for any replacement due to heat melting wheels on rack.

Took stud out of old wheel, put new stud in. It was that easy!