GLD2800T05BB General Electric Dishwasher - Instructions

No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!

Just like the video and replaced it

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.

Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.

Very Easy! Lift old arm out and replaced it with the new one.

After removing the front panels, I removed two screws holding the valve in place. I turned off the water supply and removed the water line, unclipped the hose clamps and took the faulty valve out. I then reversed the above steps and turned the water back on. NO leak. Very easy to do andthe repair took ~20 minutes to complete.

Checked availability of replacement machine and replacement parts online..in this process, I ran across a similar story by someone who fixed similar problem on a similar machine. Before removing the fill valve, I tried to confirm that it was defective my reading solenoid coil continuity. It looked ok so I could not use that info to confirm a bad fill valve, although that possibility was not eliminated. So I ordered a replacement fill valve, removed existing fill valve and took a long position on paper plates. On delivery of the valve, I found that its mounting bracket (which forms a part of the supply pressure boundary) had been redesigned to conform to a year-2000 redesign of the machine. Valve instructions allowed for this and provide for retention of mounting bracket from old valve for use on new valve. Instructions indicated the o ring from new valve (vs old) should be used in attaching the old bracket. I found that the o ring groove in the new valve was so deep that o-ring compression on reassembly was prevented. I went ahead and put together with new o-ring. When turned on supply pressure, it began leaking immediately, so I shut down, removed valve again. During this (2nd) reassembly, I stacked both o rings in same groove in order to get compression at all. Reinstalled valve w/ both o rings....no leaks and it works. I think valve design should be reviewed and depth of o ring groove reduced so only one o ring is needed.

One of the rack slide end caps broke so only one end cap kept the rack from falling out. The video guide worked for me to remove the remaining end cap allowing the rack to come out. I then replaced the middle arm conduit carrier as it no longer had a tight fit. I then replaced the middle spray arm bearing and reinstalled the rack and the rack slide end caps using the video supplied online by this site . Ran dishwasher and verified middle spray arm was turning.

Took screws out that hold front panel on, unplugged wiring, changed soap dispenser, and put everything back together. Not a bad repair at all.

Replaced lower spray arm

Press endcap in place after ensuring the rack is in track

Disconnected water, drain, electrical- remove dishwasher.
Place dishwasher on back removed part- replace with new part-reconnected and reinstalled.

It was so easy-just popped the end peice in and it fit perfectly. I also ordered 2 knobs for my dryer which was only one year old, they were also so easy to put on.. I received my parts 2 days after I ordered and because of some problems with my computer had to talk to the operators and was very pleased and happy with their help and with the parts that I ordered. I wil always order my parts from Parts Select.

Replaced the plastic piece. Simple