GLD4500R10CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gail from Woodstock, GA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
axle for wheel was broken
Popped the axle on to the wheel, then snapped it on to the lower drawer - done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Durango, CO
- Parts Used:
- WD12X10278, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
some wheels had broken, was really hard to move rack in and out.
I am NOT handy, but my husband was gone when the wheels and stud/axles came. I was able to replace all of them in about ten minutes with no tools. Easy and no more frustrations!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Mashpee, MA
- Parts Used:
- WD12X10278, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the lower rack wheels had fallen off and melted
The best money I've spent on a repair. Easy. The lower rack now rolls in and out smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Carlisle, PA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Detergent cap would not stay closed
After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ILONA from AUSTIN, TX
- Parts Used:
- WD12X10278, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one wheel was missing, others kept on falling off
Just snapped studs and wheels together and put them into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LELAH from LANSING, MI
- Parts Used:
- WD35X21035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels on the upper basket had broken
I removed the plastic end caps by gently pushing and twisting them. Once the end caps were off the basket slid out. The old wheels were removed and the new ones clipped in very easily. I then slid the basket back into place and replaced the end caps. The most difficult part was removing the end caps. I was afraid that I would break them, but by being careful and not forcing the piece they easily came off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donna from walworth, NY
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
upper dishwashr rack lost the end cap and the rack kept coming off the track when you went to push it back in it would jam into the track and all the dishes would bang and fall.
placed the end cap into location and forced it into place. Fixed -and we are all much happier!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Waterville, ME
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from LAKE WALES, FL
- Parts Used:
- WD08X10059
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom door seal had crumbled with age
Removed inside of door, slide bottom seal on and put inside door back on. Job done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from NEOLA, UT
- Parts Used:
- WD13X10066
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
its wasn't latching so the dishwasher wouldn't work unless i held the door in the whole time
I called your tech and she sent me a awesome video that made it so easy to fix on my own
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from MECHANICSVLLE, VA
- Parts Used:
- WD28X10177
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken silverware basket
Pulled the old one out and placed the new one right into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Faye from E STROUDSBURG, PA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old wheels kept falling off
Took stud out of old wheel, put new stud in. It was that easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WALNUT CREEK, CA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken axle which hold wheel on lower rack
Easy install, snap in new axle and put wheel on stud. Be sure to check all wheels for any replacement due to heat melting wheels on rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SOUTHPORT, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap broke
Slide it into the arm until you hear it snap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ARTHUR from OAK PARK, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Detergent dispenser did not work
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Was this instruction helpful to you?
Thank you for voting!