GLD4456R00CS General Electric Dishwasher - Instructions

Got the part the next day.. opened it and just screwed into place!
Easy as could be. Thank you!!

Installed new lower rack wheel kit

This repair was a snap. The parts, though not identical to the original, fit perfectly. I was able to snap both the Rack Slide Cap and the new wheel axle to the existing washer cage and the machine works great now.

Thanks for the quick delivery and great website!

Ordered the new parts and attached to wheels on lower rack. The old pieces clamped on and the plastic stretched out and would not hold any longer. The 8 new pieces have a slightly different design, were easy to intall and I believe will never loosen up.

Hired my neighbor, who is a plumber.

Removed the stops at the end of the upper rack, removed the old rollers. Replaced with new rollers and installed the stops back in place. Very easy, finished in less than 15 minutes. Replacement rollers very much improved with design from the original rollers.

Followed the instructions that came with the my order

I took the old one off and replaced it with the new one, which fir perfectly.

Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.

Removed two upper rack rail end cap stops. Removed upper rack. Replaced four old upper rack rollers (wheels) and installed four new upper rack rollers. Replaced upper rack in correct position. Installed two new upper rack rail end cap stops. The new end caps were different from the old ones, and the new wheels had shorter retaining arms than the old ones. Once observing the differences, the new parts fit properly and perfectly.

The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.

changed the door gasket no tools,just pulled out the old,lined up the dot (printed on gasket)on the new and started at the top pushed in the new took five minute,the short bottom door seal required a phillips head screwdriver to remove the inside door screws(six screws) the two on the bottom are different they attach to the door hinge and are machine thread the other four are coarse thread.lifted off the panel slide off the old(pay attention to which way the curve goes) slide on the new replaced the panel put in the six screws.the job is done! the door will be tight to close but will be easier after a few uses.

I first watched a video on trouble shooting on You Tube. I took the insides of the dishwasher apart and found broken glass and some other debris.I shop vacuumed the inside and the dishwasher pump put back together and ran a rinse cycle,unfortunatly dishwasher was not draining. Got the model number and ordered the dishwasher pump through Part select. Within in a few days I had the part in hand and had to remove the dishwasher from under counter. Once turned over the pump was right there ands took 5 minutes to change replaced pump put everything back together and now dishwasher drains as expected.

Had to replace the top rack in the dishwasher. Removing the top rack was a tricky. Have to push the tab out not in on the stopper ends of the rack. Unscrew the bolts on the water sprayer. Need to slide the sprayer instead of unclipping it. Real easy to do once it is realized. Should have taken 30 minutes if I knew this in advance

The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.