GDWT200R30BB General Electric Dishwasher - Instructions

Lower assembly only require removal and replacement without tools. Upper assembly required screw driver and pliers to install water wand from old rack to new rack.

The most surprising aspect of this repair was the short 36 hours that it took from order placement to product receipt.

Remove screws holding old hose. Attach clamp to new hose with nut driver. Tighten hose and clamp around attachment.

Easy as cake. Perfect part!

We removed the remaining rollers, inserted the studs into the rollers and attached to the lower rack. Easy. I can't believe we put up with this for so long. We appreciate your quick service. So much easier than going shopping and waiting for the parts to come in and then having to go pick them up. Thanks for being there.

Removed the wire clip, then removed two screws on mounting bracket. Then disconected the hose. Removed the brass elbow.

Then reversed these steps and I was done.

No tools required. The seal just pushes into a channel around the tub. The lower ends are held by a wire that spans the lower edge of the door. I started with the lower end since I didn't know just how the seal was installed and found the wire that sticks into the hollow center of the end of the seal. The seal just pulls out so removed it and the wire. Cleaned the seal channel and wire and installed the new seal starting at the bottom and working upwards. after the lower ends are anchored,I found the center of the seal and upper channel and pushed it in place and worked around the corners and down. I did that because I have seen seals stretch as you push them in place and end up in the middle with excess material you have to work back into the seal channel.

I took the front off of the dishwasher door, loosened the screws, unplugged the module and replaced it with the new module. This repair was the easiest repair I've ever completed!

1. Removed the cap ends from the inner rails - easy

2. Removed the old rusted rack from the inner rails- easy

3. Removed the spray arm and conduit - a bit difficult: there's a hard-to-reach nut that you need to remove at the hub of the spray arm - A pain in the neck because it cannot be reached vertically.

4. Installed the spray arm and conduit onto new rack. Make sure the conduit aligns with the pipe at the rear inner wall! - easy

5. Installed the rack onto the rails - easy

6. inserted the cap ends - done!

This is one of those things that after you do it, you wonder why you didn't do it sooner. Installation was a snap - literally. All I did was remove the wheels from the bottom dishwasher drawer (they didn't stay on anyway...and one had fallen off mid-wash and melted). I was able to re-use the wheels and simply snap in the new axels - which have a far superior design. I ordered a couple extra wheels to replace the one that melted and to have on hand...just in case. Delivery was incredibly fast - I received the parts the day after I placed the order. Why didn't I do it sooner?!

Turn off water .Remove 4 screws holding lower front panels.Remove panels, valve is on left . Remove 2 screws that hold valve , slip valve up over clip. Using pliers slide clamp back, remove hose from valve.disconnect wire clip , unscrew from water fill line. Install new valve in the reverse order

First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.

The first posted instruction is dead on (except there are 14 phillips screws (not 10) on inside of door. Also, when reconnecting the 2" quick connect, make sure it is fully inserted - otherwise the numbers on the display panel will not show correctly. Mine didn't the first time, and I had to re-open the door panel and giggle around with the connection to get the numbers to display properly.

Received part, removed lower panel and shut water and power off to appliance. Used flash light to see under dishwasher, removed the two screws that held part in place. Loosed clamp that held the water tube in place to part. Placed towel down to catch water. Pulled the line out so I could get to the nut that is attached to inlet part. Unhooked the plug after all water was gotten up. The main knuckle that's attached to the pump was on so tight that I took it to my local gas station for an mechanic to unscrew it for me....I have arthritis in my hands. Station is only two mins from me and wasn't a problem for them to do for me. Came back put fresh Teflon tape on joint and reattached it to new part. Attached all hoses and clamps, plugged electrical prongs back in and attached bracket back to body of dishwasher. Turned water on and checked for leaks. Turned power back on and ran a cycle of dishes to wash....all went well. If the knuckle was on so tight the job would have only taken about 40 min at best.

The repair itself was simple. I replaced the broken plastic pulley and the cable attached to the door and spring because one end was bent. I also had to remove the fitting that held the pulley in place. In order to access the spring, I had to pull the dishwasher way out and that required disconnecting the water supply, the drain tube, and the electrical wiring! Then I had to reconnect everything. So although the repair took less than 30 minutes, the rest of the work took a couple hours.

Open dishwasher and remove the bottom spray wheel, filter, and unscrew the mounting bracket to release the pump connector below the bottom of the unit. Remove mounting screws at top front of dishwasher and carefully slide the unit out; you may have to pry side panels inward with a flat screwdriver in order to get the dishwasher past any cabinetry. Be careful not to pull the dishwasher too far out as the water supply and drain hoses could be damaged. Unplug the unit. Turn unit sideways and tip over onto its' back. At this point, the sump will have to be removed using a nut-driver and/or socket set. This will open access to remove the old pump connector. Replace the old connector with the new connector, and reassemble the sump, connecting and firmly tightening all connectors. Tip unit upright. Screw mounting bracket back into the bottom of the dishwasher and put the remaining parts back. Before pushing the unit back into it's nook, I advise running a quick cycle just to make sure there is no leakage. If there is no leakage, put the unit back, tighten the mounting screws and you're done.

Turn off power and water from dishwasher. Remove Base Access Panel. Remove the upper 2 screws that holds the dishwasher in place. Pull out dishwasher. Locate the valve and remove the 2 screws holding the mounting bracket. (I used a hex Nutdriver to remove the screws) Remove the valve. Disconnect the wire connector. Disconnect water supply. (Place a towel to catch the water) Loosen the hose clamp holding the inlet hose and remove the hose. (I used pliers to loosen the clamp) Remove the elbow from the old valve and reattach to the new valve. (Use teflon tape around the threads) Reverse the Process. Check for leaks. Piece of Cake. Part was an exact fit.