GLD2800T10WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Lynn, MA
- Parts Used:
- WD26X10046
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher was not draining
I first watched a video on trouble shooting on You Tube. I took the insides of the dishwasher apart and found broken glass and some other debris.I shop vacuumed the inside and the dishwasher pump put back together and ran a rinse cycle,unfortunatly dishwasher was not draining. Got the model number and ordered the dishwasher pump through Part select. Within in a few days I had the part in hand and had to remove the dishwasher from under counter. Once turned over the pump was right there ands took 5 minutes to change replaced pump put everything back together and now dishwasher drains as expected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Estelle from Queen Creek, AZ
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We had a rip in our tub gasket.
I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from MACKINAW, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The detergent dispenser latch was broken
The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Woodstock, GA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
axle for wheel was broken
Popped the axle on to the wheel, then snapped it on to the lower drawer - done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Carlisle, PA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Detergent cap would not stay closed
After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donna from walworth, NY
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
upper dishwashr rack lost the end cap and the rack kept coming off the track when you went to push it back in it would jam into the track and all the dishes would bang and fall.
placed the end cap into location and forced it into place. Fixed -and we are all much happier!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LELAH from LANSING, MI
- Parts Used:
- WD35X21035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels on the upper basket had broken
I removed the plastic end caps by gently pushing and twisting them. Once the end caps were off the basket slid out. The old wheels were removed and the new ones clipped in very easily. I then slid the basket back into place and replaced the end caps. The most difficult part was removing the end caps. I was afraid that I would break them, but by being careful and not forcing the piece they easily came off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Waterville, ME
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Davidson, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Cap had broken off the top rack, it kept sliding down
I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from NEOLA, UT
- Parts Used:
- WD13X10066
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
its wasn't latching so the dishwasher wouldn't work unless i held the door in the whole time
I called your tech and she sent me a awesome video that made it so easy to fix on my own
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SIMPSONVILLE, SC
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The door on dishwasher soap dispenser broke.
Repaired the soap dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from LAKE WALES, FL
- Parts Used:
- WD08X10059
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom door seal had crumbled with age
Removed inside of door, slide bottom seal on and put inside door back on. Job done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WALNUT CREEK, CA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken axle which hold wheel on lower rack
Easy install, snap in new axle and put wheel on stud. Be sure to check all wheels for any replacement due to heat melting wheels on rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Faye from E STROUDSBURG, PA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old wheels kept falling off
Took stud out of old wheel, put new stud in. It was that easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SOUTHPORT, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap broke
Slide it into the arm until you hear it snap
Was this instruction helpful to you?
Thank you for voting!