EDWF800P00WW General Electric Dishwasher - Instructions

Simply pull out the old axle and snap in the new one. It is simple. Also the replacement axels were MUCH better quality than the originals. The bottom tray now slides in and out very easily. Note, if you have this problem, you do not need to replace the wheel, just the axle.

Really all it took was removal of the old wheels which would not stay on anyway and the installation of the new ones. That required the axle and wheel being put together and the installing both of those on the lower rack. I was about to buy a new dishwasher when the salesmen told me about a product called Lemi Shine it saved my hundreds of dollars and the inside of my dishwasher looks brand new. With my new wheels I am good to go again.

but axle on new wheen and put axle on tray

This was a simple part swap. The stud rollers are the small peg-clips that hold the wheel on the lower dish rack. Removing the old stud rollers from the wheels required a pair of pliers. I then popped the new stud rollers into the old wheels and snapped them back onto the lower dish rack. I scored some major points from my frustrated wife -- easy, fast fix!

Followed instructions on how-to video on website on how to remove and replace lower spray arm.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

Replaced interlock assembly as one of the possible causes. The replacement was easy, but this was not the final fix. I also replaced the water inlet valve, flood switch and finally found that there was large calcification within the drain tube assembly (not visible, but was blocking water). Got a new flexible tubing and new drain hose, plugged everything together and the dishwasher runs like new now. Watching for a potential leak from the drain tube to drain hose connection and mya need to tape it up, but so far so good...

Man, if you need help doing this repair, you shouldn't even own a dishwasher, much less a house. This was the easiest repair in the entire galaxy. First, I removed the old wheels, which was easy becasue they were always falling off by themselves. I then had to use pliers to squeeze the old studs to remove them from the wheels. All the wheels were still in good shape. Then I snapped the wheels onto the new studs, and snapped the studs onto the lower rack. And then, it was like I was in heaven. Bluebirds were singing, the sun was shining, my lower rack was sliding in and out and in and out like it was new. O happy day.

This lower rack (GE part #WD28X25960) was ready to roll right into the dishwasher straight out of the box, no tools needed.

HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!

Pulled old spray arm off and snapped new one on. Less than 3 minutes and works great. Dishes are cleaner now.

Watched the video, and followed the directions. Although my machine had some slight differences, the repair went pretty much per the video. Got all connections back where they belonged, cleaned up the insides a little while had the door parts separated, then buttoned it all back up, ran a cleaning solution thru empty washer, let it dry then started filling with dishes and ran the wash cycle the next day when full. All is well.

I watched this video: https://www.youtube.com/watch?v=-k0iZGwMOGc
And then I did exactly what it said! It was easy. Plus, when I opened the panel I could see the old switch interlock assembly was melted on one side, so I knew I had gotten the right part!

Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!

shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.