ADW1100N30BB General Electric Dishwasher - Instructions

Took old rack out put new rack

I watched the video that came with email on part. Gave instructions on how to. Thank you !

Ordered most likely part...water inlet valve.

1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.

Our older GE dishwasher was leaking water on the floor while running. After inspecting it while running I was able to determine that the water was coming from the seal around the motors shaft where it entered the pump. I then looked up the washers model number and ordered the impeller shaft seal kit. To my suprise the kit arrived the very next day! After disconnecting the power and water supplies from the dishwasher , I then removed it from the cabinet base and turned it over to gain easy access to the bottom. Using nothing more than a nut driver, adjustable wrench and a pair of pliers I was able to loosen the two compression clamps and two hose clamps that hold the pump to the bottom of the washers tub. I then removed the entire pump and took it to my work bench for the rest of the repair. Removing the plastic impeller strainer was the toughest part.. Lacking the proper spanner wrench, I had no tool that would lock onto the raised tabs to turn it loose with. I was able to position the tabs in the jaws of my workbench vise and giving the entire pump a little twist, It broke free and I was then able to unscrew the rest of the way it by hand.. The old dried up detergent made for a good adhesive, and after removal I cleaned the area completely so the new strainer would thread in easy. I installed the new parts in the kit as per the supplied instructions and re-installed the pump housing back on the dishwasher and put it all back in place. After running it several times not a drip was to be seen, and I was very pleased with the whole process. With the shipping it cost me just $25.00, and it saved me a expensive service call or maybe even the cost of buying a new machine. I would say that overall it was a easy repair but lacking the right tools, you may have some trouble removing the pumps plastic strainer screen as I did. I would highly recommend PartsSelect to anyone, and the entire experience was a good one for me.

The part came in as ordered. After removing the dish rack, I loosened three 1/4" screws (two on the strainer basket and one at the base of the spray arm. I had to slide the rubber hose down and back to disconnect the base which I did by turning counter clockwise. The new one went in by reversing what I just described. Other than two of the screws being difficult to reach, everything worked fine.Thanks for your site.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

it was super easy and the part came in days. it was super quick

Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.

Took out the old one and put in the new one! Note the delivery time was great! The part was ordered one day and delivered the next! Thank You Ed Andrews

Removing the slide end caps was a little tricky. Key was to tilt and twist the end cap and slide out. Putting them back in was equally as tricky, but reversing the process helped. Sliding the new track in place was simple. Total repair took about 6 or 7 minutes.. Part was ordered on a Monday morning and delivered the following day using standard shipping. Outstanding service.

Simply screwed in new cap

Very simple. First recieved Top rack. used a flat head screw
driver to remove cone/tower, put cone on new rack. put rack
on grove slided in easily. Took old rack out.replaced with new easily

I turned off the water supply to the dishwasher. Then took off the front panels and disconnected the water. I then unscrewed the dishwasher from the countertop, pulled it out luckily there was plenty of play in the wire, and drain hose. I turned it on its side and had to remove a couple clamps to free th piece that I was replacing. Once I got to it, it just unscrewed. I put the new one on and everything back together. It was easy.

The replacement of door rubber seal was easy as well as the corner boot tub baffles. I did take the door off to make cleaning and installing seal easy. I wish your web site would recommend if replacing certain parts, additional
parts should be replaced at the same time. For my project I should have
replaced the 3 inch separate seal located inside bottom of door. You can't
see it until removal of the door. I am thankful for the easy to follow
instructions other people wrote and it made the job much less stressful..

Thanks again