ZBD3500ZZ2WW General Electric Dishwasher - Instructions

The finished accent panel on my GE dishwasher was dented and looked awful in my newly remodeled kitchen. I thought about purchasing a new dishwasher but instead searched the web for the part. Found Parts select and it was so easy to compare my part with the graph picture provided. Just count off the boxes for measurement and you will know if you selected the part you need. Access panel arrived in two days,packaged well, and I am happy to have found this website. Give it a try....and returns are easy too if you make a mistake in ordering. My order was perfect on the firt try.

Starting removing the screws based on the Users guide document - was surprised to find 4 different types of screws and driver heads - Luckicly I am an adult male and have every tool -

the surprise were the Star screws - the phillips head and soctket screw were one thing -

Everything went well.

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.

The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.

The dishwasher runs quieter and the dishes come out clean now.

Partselect was the only one that had the correct solution. The Piston and Nut assembly fix the problem. The washer on top of the piston was worn and it would not fully close. Replace the piston and nut assembly within 15 minutes after I found it.Shipping was supposed to be within 3 days. The part came the next business day during the thanksgiving holiday. WOW

I put on my rubber gloves, removed the lower wash rack, removed four screws from the drain guard. I unscrewed the defective part, installed the new assembly and hand tightened. Replaced the cover and installed the screws removed earlier. Re installed the lower tray, and ran the rinse and drain cycle. It has been working beautifully ever since.

Remove the screen that runs along the back of the dishwasher.In the middle of the area that was covered with the screen you will see a white plastic valve with 2 little ears sticking up. Use the nose of a pair of pliers to twist counter/clockwise on the valve and it will come right out. Inspect the valve.If the rubber cone shaped valve inside the valve can be pushed through the top of the valve ,the valve is bad.Replace it and go wash your dishes.

Removed the 4 1/4" screws holding the rear screen to the bottom of the inside of dishwasher. "Piston & Nut" assembly was badly corroded- to the point that no dirty water was leaving the dishwasher. Because the appliance is at least 10 yrs old and there was nothing happening during the rinse cycle, I initially assumed the worst- that the pump was bad. After reading the other descriptions of the problem here, I said, "what the hell?, if a $20 part fixes it, I'll be amazed- if not, I'm out $20 and looking at another $300 for a new dishwasher!" The $20 part (inc. shipping) did the trick. Thank you, and your website is on my "highly recommended" list! One note- the piston & nut assembly did offer some resistance as you might expect after being "gunked" in place for 10 years. However, the top has some lugs or ears built into it, so a few taps with a hammer on my largest straight-blade screwdriver loosened it right up...

Looked online for a general cause. ABout 60 to 80 percent, the cause was the piston and nut assembly located in the back of the dishwasher. Ordered the part and installed in nothing flat. Only four nut screws to remove the take the filter off and unscrew the piston and nut assembly. Next cycle, no water and the drying cycle seemed to be better. Guess because no water in the bottom of the dishwasher. Good input and fast turn around on the part.

Piece of cake. All done and working just fine.

Originally replaced solenoid without pulling unit out, but continued to leak. Purchased the entire motor and pump kit; pulled unit out, turned it on end and replaced the motor. The only problem was that no new ground screw was sent with the kit and the existing screw wasn't quite short enough to connect. Either the hole on the replacement kit needs to be deeper or a bond screw needs to be sent that will fit the new kit. We had to find our own screw that would fit properly.

followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which was not present on my original however it installed perfectly and no longer leaks.

Remove old piston assembly with screwdriver and tapping hammer inside the machine and screw the new part in hand tight, all done works fine

All new seals

The part that took the longest was taking the washer out from under the counter. The fix was the easy part = 15 to 20 minutes no problems. After putting the washer back and reconecting everything,the first cycle I had some leaking around one of the two big clamps. I had to pull it out again and move the clamps around and tighten them. Much better the 2nd time around, Good to go!! HAPPY WIFE HAPPY LIFE !!!! Good Luck !!