GSD5920D00BB General Electric Dishwasher - Instructions

First I opened the package and screwed the new dispenser cap into place.

The Solenoid black plastic had melted around the solenoid shaft. I unplugged the solenoid, removed 2 screws,then one C clip and pulled the the unit out. The new solenoid is difficult to install all together as the shaft it goes on holds it all together when both springs are installed - - so I installed in one piece, with the 2 screws, except for the white plastic thing, the C clip that holds it on the shaft, and one of the two springs - - these three items went on separately. I wanted to thank the help your expert gave, but I couldn't figure how to do that.

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!

Turn off power at breaker box.
Remove lower covers and 2 screws into counter top.
Verify sufficient length on water and electrical connection to allow sliding dishwasher out approx. 2/3. I disconnected the electrical at the j box on the dishwasher. If you must disconnect the water line, shut off supply, usually located under nearby sink, and provide a rag or sponge for small amounts of water left in supply line.
Carefully pull back the insulation to expose two screws on top where water line runs into the center.
Pull the top tray part way out and reach in to hold the spray arm while removing the screws. The spray arm will easily drop out.
Hold the new spray arm in place making sure the raised screw posts push into the holes, then reinstall the two screws. Done. Pull insulation back into place, retape if necessary. Reconnect electrical and water if necessary.
Slide unit back in, checking alinement. Rescrew to counter top and reinstall lower covers. Task complete. 15 mins if prepared. 30 mins if both elect. & water are disconnected and you are somewhat hesitant.

First, I drained the water from inside the washer and removed it from under the sink. I wasn't sure if I had a clog in the drain line, so I dissasembled the drain under the sink and cleaned that as well. While cleaning under the sink my wife found her $4000 dollar ruby that fell out of her mothers ring a couple weeks earlier. It must have dripped out of the trap while I had water draining everywhere. Put drain back together and moved on to the dishwasher repair. Parts were easy to install after laying the dishwasher down on its front to access the bottom back side. Hooked everything back up and slid it back under the countertop and away it went. Had one small leak after running (water in line wasn't tight enough). A twist with a pair of pliers and that was resolved.
Fast shipping by the way! I paid a little more for the exit washer than I wanted to, but with shipping only from one source and delivery of parts at the same time made downtime as little as possible. I'm sure I saved $100 dollars or so by using this website for parts and tech info. And recovered a precious stone to boot.

Ordered the part online and replaced the hoses. Very easy...took maybe 20 minutes

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.

Removed seven screws that held the inside panel to door. removed inside panel to work area and cleaned. After carefully observing the position of the old gasket, it was easily removed and the new one but in its place. Replaced the door being careful toalign the handle before tightly securing all seven screws. Repair worked, no more leak.

Simply screwed in new cap

Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

According to instructions with part

Looked up possible causes on your website. Website stated that more than 50% of time the cause was the piston and nut assembly. Removed the piston and nut assembly in bottom of unit behind screen on rear wall and saw that the gasket seal was completely gone . Ordered the part. took less than 10 minutes to install. Tested the unit and it drained completely. Thank you as i was looking at a more difficult repair if the pump had to be replaced.Repair cost less than $20.00.Before changing piston and nut assembly I cleaned the strainer and sump. disconnected drain hose and checked for blockage . i than checked your website that listed the piston assembly as the culprit more than 50% of the time. Thanks again

I took out the old one and put the new one in.