GSD4000N10BB General Electric Dishwasher - Instructions

I took the old front panel off which wasn't hard, and replaced with the new panel. The job would have been a lot easier if I had 2 hands, but it just took a little longer. Not much of a problem really! New panel looks great!

Thank you for having the parts displayed as you did. It was easy to find-select-buy. Delivery was fast and repair was easy. Thanks Marianne

First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!

Simply replace wheel

so easy! Ordered the rollers and clips ... popped them on and done!!!

i needed new rollers and inserts to keep wheels on now its like new when i pull out bottom basket

Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!

removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.

All new seals

just snapped the new part in. couldn't have been easier

pulled the motor and impeller apart noticed that the the impeller blade bent. I got the new part and put it back together

Disconnected power at circuit breaker, removed lower spray arm, fine filter, inlet cover, and sump cap - manually drained water from inlet sump, then laid dishwasher on its side. Removed motor/pump housing, collection chamber, and associated hoses from inlet sump and extracted inlet sump from inside the dishwasher. Reversed process to install new inlet sump, paying careful attention to ensure a leak-free repair. The problem was damage to the part of the inlet sump that receives the feed from the fine filter - the inlet sump material had been damaged when I tried to clear some debris, resulting in a less than perfect seal when the motor/pump reversed and attempted to push water out of the dishwasher. New inlet sump, perfect seal, all the pressure is now pushing water out of the dishwasher during the drain cycle. PartSelect diagnostic app and parts diagrams were instrumental in being able to repair the dishwasher for less than $25.00 versus a service call costing hundreds. Thank you.

Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.

I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!

Troubleshot and found that the solenoid had burnt up locking the drain door in closed position. I ordered solenoid, Note: I only received the solenoid. I used the old bracket and springs along with the piston arm for the solenoid. I had to break it free from the old solenoid. Once I got everything cleaned up and put together it took me about 10 minutes to install the solenoid. I manually tested mine prior to wiring back up to ensure proper movement and then tested to ensure that the piston arm did not pop out of the solenoid base.