GSD4320Z00BB General Electric Dishwasher - Instructions

I opened the dishwasher, rolled out the defective/rusty Dishrack, removed it from the dishwasher and replaced it with the new Lower Dishwasher Dishrack.

Before attempting this repair, remember to remove any dishes from the lower Dishwasher Dishrack.

Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.

Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.

I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.

removed old tower uuing a screwdriver to losen the tower from rack and slid the new part into place.

Remove end caps on the slides on the upper rack pulled old rack out put new rack in push end caps back in

I had to readjust the door latch to get the door to close

The three top mounting points broke from the control panel that fasten it to the door assembly. Vent assembly mounting point also snapped. All occurred when movers tried moving the dishwasher by the control panel handle. Removed the nine screws from the control panel (six door frame and three already broken top mounting points). Position the door lock swing arm to the middle of its left/right travel, and remove the rear panel to expose the inner door. Disconnect electricity. Even though the washer is off, 110 is present at the door. Using the new control panel as a guide locate all the mounting points (screws) for the control board, sequencer, and vent control. Be careful to note the how the lever control is mounted that is located under the sequencer. Pull black and white connectors from the control board and any other connectors that interfere with the removal of the control panel. Remove control panel and reverse the order for assembly. NOTE the insert escutcheon #902 (name plate) couldn't be found anywhere, can be removed from the old control panel and reused. Very carefully working from the bottom of the name plate use your fingernail (not a sharp object) and start to work the plate loose from the control panel. Work to the end without the brand name until you loosen that end. Slowly pull up at a 45 deg angle and it will slowly come loose. Be patient. They use a sticky rubberized glue. Good luck!

I am so pleased with Parts Select. I placed my order on Sunday night and the parts were here on Tuesday morning. the install went well except for a small handful of spare parts! Anyway it looks like new and runs with no leaks.

This was really easy. The parts fit perfectly. First i turn off power at circuit panel; turn off water and dissconnected water line and discharge hose. Removed dishwasher from under counter and placed on side. Disconnected connections to motor and pump and replaced and installed same as one unit.

Held panel in place and drilled holes and installed drill screws.

Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.

Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!

Removed old gasket, cleaned grooves, installed new gasket

Followed easy instructions and completed repair in less than 30 minutes.