GSD2000J01CC General Electric Dishwasher - Instructions

Had to pull the dishwasher from under the counter to access the water inlet valve. Disconnected the hoses from the inlet assembly. Removed the inlet assembly from the dishwasher frame. Installed the new assembly and reconnected the hoses. Plugged the dishwasher in, selected a cycle to run to check for leaks.

My husband said it was easy. But the gasket didn't solve the problem. So we had to order another part. We had to order the little black stoppers that go in the hinge area. Still leaked so my husband took them back out and cleaned the area. Then put some kind of sealant in and replaced the black robber things. So far that worked.

First I turned off the breaker so all the power was off to the dishwasher. Then I removed the door handle, which has one screw on the bottom side. Next i pulled the timers handle off, just pull it straight out. Next i opened the door on the dishwasher and removed the 8 screws on the back of the door. Next i pulled the door panel apart to get to the timer. I disconnected the three plugs from the old timer, then unsrewed the two screws holding the old timer in place. Put the new timer in, and put it all back together. The new timer works great and it solved the problem

We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.

I took the old one off and replaced it with the new one, which fir perfectly.

I removed the dishwasher, removed the front kick panel, layed the dishwasher on its back, loosened the clamps and removed the old motor and pump assy. Cleaned up the area where the unit was, Installed the new unit, tightened the clamps and it was done. Probably took around an hour because of my cleaning up the sealing areas.

See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.

The instructions provided are very good if I had done before. My concern was getting the gasket to sit properly at the bottom where you cannot see. I removed the inside of the door (7 screws) and this made it easier to assure gasket sat properly in the track. may have cost an extra 15 minutes but worth it. If I do again I will take door apart again, however I think this is fixed and should not need attention again.

First of all this site is awesome. So helpful in diagnosing and ordering the part. I highly recommend!

So, the solenoid was melted and needed to be replaced. If you're looking from the front of the dishwasher it's on the left side and it has 2 screws and a c ring. I couldn't get the c ring back on, but the piece stays on without it. Works fine now.

I removed the two screw at the top holding the dishwasher to the counter top; pulled on the unit - but found it stuck on something.
Of course the hot water feed and the drain hose were still connected and would not let the unit move out any further as there was no slack.
If I had thought about it - I would have disconnected these from under the adjacent sink. But I ended up lying on the floor trying to disconnect them from underneath the unit. It was a bit difficult as there was very little room to move the wrench and the screwdriver.
Once done, the unit came out very easily.
When tipped over I disconnected the old motor and replaced with the new. It was a very different design but fitted in very easily. The hanger took a bit of working out as the diagrams are not very clear.
The wires and clips went together easily. Once I had cleaned everything around the motor and the gunge that cames from years or washing dishes, it went back the way it came out. Albeit with the same difficulty with feed and drain hose.
We ran the unit with no dishes for a couple of times to clear our the muck left in the pipes when the system was down.
Now we have a fully functioning dishwasher again. Cost $250 for the pump and motor as opposed to the $800+ unit my wife was looking at!

Hired my neighbor, who is a plumber.

I used the pump/motor replacement kit. It was a very easy repair and the parts were a direct replacement with no modification necessary. I saved over $300.

Order the part through you guys and also ask to see if there could be something else wrong. I got an e-mail back the first buisiness day and you sent me the part that day also. I installed the coil and it's be running good ever since. Thanks for your speedy service and technical support.

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.