GSC3400ZZ0BL General Electric Dishwasher - Instructions

Looked online for a general cause. ABout 60 to 80 percent, the cause was the piston and nut assembly located in the back of the dishwasher. Ordered the part and installed in nothing flat. Only four nut screws to remove the take the filter off and unscrew the piston and nut assembly. Next cycle, no water and the drying cycle seemed to be better. Guess because no water in the bottom of the dishwasher. Good input and fast turn around on the part.

follow instructions found here, with a little help from part diagram. Initially removed the sump cover but then removed the cover at the back of tub. This uncovered the Piston assembly and the replacement was a snap. Dishwasher now works well and actually cleans the dishes. Also did I mention my parts arrived the day after I ordered even though I used standard delivery. This site rocks.

Followed the directions from the website and removed the plastic screen from the back of the washer (4 bolts). The Piston and Nut assembly was easliy removed with a few turns, popped the new one in, and re-installed the screen. Everything works great.

Turned off breaker. Turned off water and disconnected water line to make it easy to pull unit out and turn on it's side. Once that was done it was an easy swap out. Exact same motor/pump assembly. Love this site. Thanks

pulled washer out and turned it upside down to get to the pump&motor.
no problem to fix

Unplugged the machine then removed the two connectors to the motor. Loosenned the hose clamps, pulled the hoses took off the balancing bar,removed old motor assembly and put new one in. Reverse all the steps plugged the machine back on and was done in less then twenty minutes.

removed piston in filter and replaced. the check valve had come apart and was not sealing

First I removed the four screws from the screen/cover located at the back of the dishwasher. You will notice a mesh screen in the center of this cover. The check valve is under this cover midway between the sides. The check valve is unscrewed counter clockwise. I had to use a pair of pliers to start turning the valve. There are two "ears" on the top of the valve. You will see a rubber cone shaped piece that should completely cover the opening when the plunger is depressed. In my case the rubber was almost completely gone allowing water in the drain hose to return to the dishwasher after the drain pump stopped. The new check valve threads back into the opening and should be finger tightened. Replace the cover/screen and you should be good to go.

Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.

Replaced the Piston and Nut Assembly, located inside the dishwasher under the screen at the back, by unscrewing the old one and replacing with the new - Works great now!!

Assistant helped me take apart unit, assumption on issue was correct, part was ordered and showed up 3days later. I installed and all seems fine. I do question what would have happened if the deduction was incorrect. The assistant was very patient and clear with his instructions. A good experience!

Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.

I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.

removed old tower uuing a screwdriver to losen the tower from rack and slid the new part into place.

The dishwasher would drain correctly 3 out of 4 times and the original part did not appear to be in bad shape. Decided to change anyway based on posted success rate in resolving the issue and the low cost of the part. After one month of daily operation the issue has been completely resolved. Could not have been any easier!