GSD4020Z05BB General Electric Dishwasher - Instructions

Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy

I removed the dishwasher, removed the front kick panel, layed the dishwasher on its back, loosened the clamps and removed the old motor and pump assy. Cleaned up the area where the unit was, Installed the new unit, tightened the clamps and it was done. Probably took around an hour because of my cleaning up the sealing areas.

The instructions provided are very good if I had done before. My concern was getting the gasket to sit properly at the bottom where you cannot see. I removed the inside of the door (7 screws) and this made it easier to assure gasket sat properly in the track. may have cost an extra 15 minutes but worth it. If I do again I will take door apart again, however I think this is fixed and should not need attention again.

First I removed the two screws that hold the solinoid in place,then I removed the e clip and unpluged the wire and pulled out the plastic lever with the solinoid and springs. To install Solinoid:First I bolted on the bracket ,then I hooked in the spring in the plastic lever and installed lever on shaft then I hooked in the long spring to the bracket small hole in the bottum then I installed the e clip next I pluged in the wire.Then I tried the Washer .Averthing works fine.

Order the part through you guys and also ask to see if there could be something else wrong. I got an e-mail back the first buisiness day and you sent me the part that day also. I installed the coil and it's be running good ever since. Thanks for your speedy service and technical support.

First of all this site is awesome. So helpful in diagnosing and ordering the part. I highly recommend!

So, the solenoid was melted and needed to be replaced. If you're looking from the front of the dishwasher it's on the left side and it has 2 screws and a c ring. I couldn't get the c ring back on, but the piece stays on without it. Works fine now.

i unscrewed old part and replaced with new one. Didn't know how to do it but figured it our quickly.

Removed screws from back of door, a few more inside retaining the control panel (and a couple more from a small obstructing part located over a corner of the control panel). Then release/pull out the harness wires and tilt out the control from its retaining clips. Biggest problem was figuring out that the control panel was still being retained only by a stubborn clip that hung up in a slot on the control panel. Pliers were needed to pull out on the clip while tilting out the control panel. Replacement part then snapped in easily after its tabs on the bottom are inserted in the slots. Didn't have any trouble with the latch - - do not sure what the other entry means about being careful with the latch.

from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..

Removed screws and replaced the part. It couldn't of been earlier. Only problem this kit didn't include a toe kick and we are having a hard time finding it.

At first I thought I would call a repair man.Then I thought-that will be at least $100!So we went online and found the part.Took about four days to arrive.I pulled the dishwasher out and turned it on it's front.The little leaking hose was easy to remove,two clamps,and the new one installed.Total cost-$14.00.

Open door, remove lower wash rack, remove 4 screws holding screen in rear of inside tub with 1/4 inch socket. Unscrew piston and nut assy for checkvalve, sounds like a mouthful but it is only 1 part. Checkvalve has 2 small ears on it which allow you to twist it out, it has treads on it. Flapper on check valve flapper rots away and water pumps back into tub instead of being routed to drain line to garbage disposal. Part with shipping was just over $20.

Bulk of time was spent in diagnosis, eliminating other possible causes for the problem, such as wall switch and door switch and timer -- done with multi-meter.

Replacement of the control module was relatively easy, but **IMPORTANT TIP** Be sure to pull the specific model jumper wire from the old control module and re-attach it to the new replacement module. Otherwise, you'll just get a continuous blinking "clean" light and the dishwasher will not operate at all.

Ordered motor and pump and replaced. Motor pump kit also comes with a drain solinoid so if that was the problem the kit repaired it. One issue is the size of the hanger to ensure the pump does not just hang on its mount. The directions were not very clear and after some trial and error I got it to work to.