GSD4940C00SS General Electric Dishwasher - Instructions

I read the reviews on line and followed the advice the part was easy to find and easy to replace once I got the screen off it came right out with a twist. and right back in reverse order, I fired it up and it drained, yay! no more stinky mess and no call to the appliance repair guy,

First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!

first I removed the screen in the back of dishwasher and then I replaced the check valve

pulled washer out and turned it upside down to get to the pump&motor.
no problem to fix

Removed the 4 1/4" screws holding the rear screen to the bottom of the inside of dishwasher. "Piston & Nut" assembly was badly corroded- to the point that no dirty water was leaving the dishwasher. Because the appliance is at least 10 yrs old and there was nothing happening during the rinse cycle, I initially assumed the worst- that the pump was bad. After reading the other descriptions of the problem here, I said, "what the hell?, if a $20 part fixes it, I'll be amazed- if not, I'm out $20 and looking at another $300 for a new dishwasher!" The $20 part (inc. shipping) did the trick. Thank you, and your website is on my "highly recommended" list! One note- the piston & nut assembly did offer some resistance as you might expect after being "gunked" in place for 10 years. However, the top has some lugs or ears built into it, so a few taps with a hammer on my largest straight-blade screwdriver loosened it right up...

Turned off breaker. Turned off water and disconnected water line to make it easy to pull unit out and turn on it's side. Once that was done it was an easy swap out. Exact same motor/pump assembly. Love this site. Thanks

Unplugged the machine then removed the two connectors to the motor. Loosenned the hose clamps, pulled the hoses took off the balancing bar,removed old motor assembly and put new one in. Reverse all the steps plugged the machine back on and was done in less then twenty minutes.

Followed the directions from the website and removed the plastic screen from the back of the washer (4 bolts). The Piston and Nut assembly was easliy removed with a few turns, popped the new one in, and re-installed the screen. Everything works great.

Looked online for a general cause. ABout 60 to 80 percent, the cause was the piston and nut assembly located in the back of the dishwasher. Ordered the part and installed in nothing flat. Only four nut screws to remove the take the filter off and unscrew the piston and nut assembly. Next cycle, no water and the drying cycle seemed to be better. Guess because no water in the bottom of the dishwasher. Good input and fast turn around on the part.

follow instructions found here, with a little help from part diagram. Initially removed the sump cover but then removed the cover at the back of tub. This uncovered the Piston assembly and the replacement was a snap. Dishwasher now works well and actually cleans the dishes. Also did I mention my parts arrived the day after I ordered even though I used standard delivery. This site rocks.

The part that took the longest was taking the washer out from under the counter. The fix was the easy part = 15 to 20 minutes no problems. After putting the washer back and reconecting everything,the first cycle I had some leaking around one of the two big clamps. I had to pull it out again and move the clamps around and tighten them. Much better the 2nd time around, Good to go!! HAPPY WIFE HAPPY LIFE !!!! Good Luck !!

followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which was not present on my original however it installed perfectly and no longer leaks.

I took the old front panel off which wasn't hard, and replaced with the new panel. The job would have been a lot easier if I had 2 hands, but it just took a little longer. Not much of a problem really! New panel looks great!

Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.

First I removed the four screws from the screen/cover located at the back of the dishwasher. You will notice a mesh screen in the center of this cover. The check valve is under this cover midway between the sides. The check valve is unscrewed counter clockwise. I had to use a pair of pliers to start turning the valve. There are two "ears" on the top of the valve. You will see a rubber cone shaped piece that should completely cover the opening when the plunger is depressed. In my case the rubber was almost completely gone allowing water in the drain hose to return to the dishwasher after the drain pump stopped. The new check valve threads back into the opening and should be finger tightened. Replace the cover/screen and you should be good to go.