PDW8700J00WW General Electric Dishwasher - Instructions

See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.

1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

Simple install- just roll it in. Fit perfect. Better design than OEM part. Perfect.

After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.

I unplugged and removed my dishwasher and followed the instructions extactly repairing the pump and replacing the parts I had just received. I torgued the ring to the specified amount, installed the pump and found the impeller could not turn. I dis-assembled it all again and loosened the ring to allow the impeller to turn, reinstalled it and when I initiated the wash cycle, water began running wildly. Next step, replace motor and pump as the pump motor shaft has gone out

The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.

Easiest repair ever. My new rack arrived in three days, opened the box and slid it in. Better quality than the original. Excellent service!

parts were easy to find and the repair was a breeze. Thanks for your help.

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..

replaced clips that were much better made.

Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.

Removed empty basket from dishwasher. Placed basket upside down and removed remaining wheels from basket by detaching worn axel from attachment points. ie, No tools needed for this procedure. Once axel and wheels were removed, I squeezed the end of the old axel with needle nose pliers or regular pliers to relieve the outward pressure and pushed the old axel out of the wheels. Easy, popped right out.
Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel and
attached it to the basket at the original position. New axel grips the basket like a clothes pin would.
Continued and replaced all eight axels at this time.
Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.
Will definately re order again if needed. Thank You.

Removed the existing stud rollers with the wheels attached. Then removed the wheels from the stud roller. Then snapped the wheels on the new "Better Designed" stud rollers. Then easily snapped the new stud roller assembly in place. Piece of cake...works like a charm.

Thanks,

Randy

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.