GSC3200J01BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Victoria from Flower Mound, TX
- Parts Used:
- WD31X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Toe kick not included
Removed screws and replaced the part. It couldn't of been earlier. Only problem this kit didn't include a toe kick and we are having a hard time finding it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- forrest from stuart, FL
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace door gasket
from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Isleton, CA
- Parts Used:
- WD24X10015
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaking small hose.
At first I thought I would call a repair man.Then I thought-that will be at least $100!So we went online and found the part.Took about four days to arrive.I pulled the dishwasher out and turned it on it's front.The little leaking hose was easy to remove,two clamps,and the new one installed.Total cost-$14.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from tampa, FL
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
water left in dishwasher after wash
Open door, remove lower wash rack, remove 4 screws holding screen in rear of inside tub with 1/4 inch socket. Unscrew piston and nut assy for checkvalve, sounds like a mouthful but it is only 1 part. Checkvalve has 2 small ears on it which allow you to twist it out, it has treads on it. Flapper on check valve flapper rots away and water pumps back into tub instead of being routed to drain line to garbage disposal. Part with shipping was just over $20.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from baunbridge, GA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water remained in the dishwasher after the running cycle
After two repair people were unable to solve the problem, I read similar stories in your forum and decided to replace the check value as a last ditch effort. Looking at your diagrams it seemed like an easy repair. Removed four screws with nutdriver and replaced value by hand. Ran washer three times and water drained completely. Still puzzled that this wasn't the first thing a repair person would check.
Websight very helpful.
Websight very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Boulder, CO
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dishwasher wouldn't drain completely
Remove the back filter to access check valve assembly. Twist check valve assembly to remove, not significant deterioration of rubber cap. Install new assembly. Re-install filter. Super-easy and effective!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Johnson City, NY
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
1-2 inches standing water at end of cycle.
Remove shield in rear. Unscrew valve using hand. Screw new valve in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACALYN from TREVOR, WI
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
dishwasher didn't drain
took out 4 screws pulled piston out and changed put back together. very easy and inexpensive!! thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stan from philadelphia, PA
- Parts Used:
- WD21X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
water would not drain
Loosened the clamps connecting the pump, disconnected all electric and stabilizer arm. Simply unscrewed the solenoid bracket and replaced with new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pankaj from KENNESAW, GA
- Parts Used:
- WD09X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original knob broke off
After aligning the new knob shaft to the slotted hole and with a slight inward pressure, it snapped right in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clyde from DUNCANNON, PA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
water would not pump out of machine
I looked at your web sight and saw how to repair dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- renee from shelby twp, MI
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench set
standing water at the bottom of the dishwasher
remove the screen at the back bottom of dishwaser. (4 screws). Unthread piston and and nut assembly for check valve....thread in new one.
Problem solved....no more water $10 part....no repair person !!!
Problem solved....no more water $10 part....no repair person !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lake Como, FL
- Parts Used:
- WD24X10015
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
rear hose broke on back of dishwasher
First i removed the front cover from the dishwasher then i reached under dishwasher and removed the hose ,then installed the new one. the hose was different size on each end. it took a factory hose to fit it. The diagram that partsselect showed of the dishwasher (the breakdown) made ordering the right part a breeze. Thanks PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from longmont, CO
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
leak between motor and pump housing
repair kit was complete and directions were easy to follow. my model of dishwasher disnt even require any of the adapters. really only required removing a couple of clamps and replacing everything as a single unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonita from Alexandria, VA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
End of cycle water in bottom of nDishwasher
Removed screen bottom rear andfound a plunger type part, unscrewed plunger and found it was distressed around it and did not close of a tight seal. Placed new part into location and dishwasher now proforms perfect...
Was this instruction helpful to you?
Thank you for voting!