GSC3200J01BB General Electric Dishwasher - Instructions

I received my dishwasher as a hand me down, my Aunt never liked the way it cleaned. After it sitting for about 2 years i installed it in my house and found that it leaked all the time from where motor shaft went into the pump housing. After disassembling everything and scouring parts sites online, I found the parts, ordered them. 3 days later i had the parts, and the next day I had a fully functioning leak free dishwasher.

This is a great website. I ordered my part on Wednesday night and it arrived Saturday morning without paying any extra for shipping. Plus since I am a female, this website enabled me to easily and affordably make the repair myself without having to worry about a repair man trying to take advantage of someone that they think they can.

I first made sure that there was nothing stuck in the drain area inside of the dishwasher. That meant I had to bail out all the standing water and then unscrew the mesh cover from the bottom. Since there was nothing in there I ordered a new solenoid.

First I unplugged the dishwasher. Then I removed the screws with a screwdriver that held the bottom cover on the dishwasher. Once I could see the installed solenoid, I put together the pieces of the replacement solenoid that I bought so I was sure to install the new one correctly. That did not require any tools. Then I unscrewed the two screws that held the solenoid in place and removed the little metal ring from the shaft which was the last piece holding it in place. Getting that ring off was tricky. I ended up using a pair of tweezers to pull it off. After that I put the new part on and screwed it in with the two screws provided. The little metal ring went on much easier than the old one came off. I screwed the bottom cover back on and voila! my dishwasher was fixed.

Read about somebody else with the same problem and ordered the check valve. 4 screws off, twist out old valve, twist in new valve, 4 screws back in. Now dishes are see-yourself clean.

First I took out the two screws that hold the drain solenoid on the unit and took off the c- clip that held the arm on the shaft if you have a digital camera take a picture to make sure you can get it back together the same way.. Then put together new unit and attatched putting the c-clip back on. Ran it through some cycles to make sure the solenoid was working. Four days later the solenoid is melted again, the timer must have an intermittentant problem I should have replaced the timer and the soleniod both at the same time. Make sure you dont make the same mistake I did. Now I will be buying a new dishwasher instead of putting any more time and money into this one.

first, I removed the screws holding the dishwasher to the countertop.Then I removed the dishwasher from under the counter. I turned the dishwasher on it's back and loosened the three hose clamps securing the water connections to the pump assembly. I then removed the electrical plug to the motor and the screw holding the support rod to the motor. Then I worked the loosened water connections apart and removed the pump and motor assembly.
Then I removed the hose clamp and plug from one of the orifices on the new pump, and aligned all of the water connections and wiggled the new pump assembly into place. I tightened the hose clamps, Installed the new screw and support bar to the motor, and connected the electrical plug. I then turned the dishwasher upright, reconnected the power cord, water supply and drain lines and started a wash cycle to check the new system for leaks. I found that the extraneous drain solenoid that came attached to the new pump was loose and rattling, so I secured the solenoid shaft and linkage to the pump housing with electrical tape to stop the rattling.

Based on information gleaned from the internet, I suspected that the drain solenoid might have melted. I took apart the solenoid assembly and checked it out. I found that some of the plastic on the inside of the solenoid had indeed melted, making it impossible for the plunger that opens and closes the drain valve to move in and out smoothly and completely. I removed the old solenoid, replaced it with the new one, and the dishwasher worked perfectly.

I received panels about week after I ordered them, however the large panel came scratched. I immediately called your customer service who was extremely helpful and considerate. She ordered me a replacement and it arrived the very next day..

Excellent service, I was truly impressed.

First we got all the water out of the bottom of the dishwasher. Removed the old, melted drain solenoid. Very important - DO NOT THROW ANYTHING AWAY. The solenoid that removed was melted; however I had to reuse the springs, brackets and plunger from the old solenoid. I had to scrape and clean (with a solvent) the metal plunger to reuse it. Once I got it cleaned up and re-used the old parts, mounting it was easy. However, getting that tiny lockwasher on the shaft was a real pain in the ass. Finally I got it together and it worked great.

The small 4" gasket was missing from the machine, and the large gasket was bent and out of place. I ordered the small gasket and installed it into the groove, placing the end flaps behind the large gasket. The large gasket was questionable, but I did not replace it. It seemed OK after I snapped it back into the door groove. Once the gaskets were properly aligned, I carefully replaced the inside door panel and screws. No more leak!

Removed the dishwasher, turned it over, removed 3 hoses, 2 clamps, 2 wires and one support. Installed new pump and reconnected. Done!

Shut off circuit breaker to dishwasher and shut off valve to dishwasher under sink.Remove bottom access panel screws on both sides of panel. Remove both screws holding dishwasher to counter.Place old mattboard strips under legs to prevent scratching floor & slide out from under counter. Use a Shopvac to remove water and spillage. Have rags and paper towels handy. Carefully disconnect wires, drain hose and water line to free dishwasher. Fold old rug runner in half to place dishwasher on, turn on side and then gently upside down on rug to access motor. Remove butterfly clamps, hose clamps, electrical connections, and support bracket. remove old motor and pump and place in box to discard. Position replacement motor and pump according to diagrams. Reconnect all clips, hoses and connections. Since replacement motor and pump is smaller, use longer support bracket from adapter kit. Return dishwasher to upright position and reconnect wiring using wirenuts, drain hose and waterline. Reposition mattboard strips under legs and slide back into place. Attach screws to counter top. Turn on power, water and do a test run to check for leakage. Replace bottom access panel. Pat yourself on the back since you've saved yourself hundreds of dollars for a repair or replacement of your dishwasher.

I made this replacement more dificult because I removed the old motor/pump earlier. Should have done it at the time I installed the new unit to be sure all hoses where installed correctly. I hooked the drain hose to the wrong port and when I started the dishwasher I found my error. Once I corrected the problem and started it again - the wash and drain cycles were perfect and there were no leaks.

After determining the drainage issue was caused by the solenoid, (by process of elimination; the hose was clear, drain opening clear, diverter moving freely, power to solenoid present during rinse cycle= bad solenoid. Solenoid showed signs of overheating upon internal inspection...) I transfered the bracket assembly to the new solenoid, re-attached bracket to diverter reservoir, connected spring and power and Did a test run. Solenoid works great! I did notice the shaft on which the diverter pivots leaking just a bit while moving the shaft. You might consider oredering a new gasket for it if you plan to replace the solenoid. Pretty easy repair. Especially considering the complexity of some other possible problems! Good luck!

Since the pump and the motor was a single unit, I removed the assembly by disconnecting the electrical plugs and drainage connections. This was a very simple installation. I reversed the above steps, reinstalled the dishwasher and all worked out well.

The repair went smoothly. There were actually instructions included with the parts, so that was nice. The only "gotcha" I found was that . . . after you take off the old food-chopper, you have unscrew the old impeller from the motor shaft. This was a bit difficult and you'll want some good pliers to do it. Don't worry about stripping where the food chopper screwed on-to, that part is attached to the impeller and there is a new one on the new impeller. When I re-installed everything onto the dishwasher, it rattled the first couple of times while the wear-ring was finding it's seat. Don't worry, that's normal. It went away by the third wash. I think I still have a small crack in the pump housing, though. The pump housing is two halves of molded plastic fused together along a seam, and I think the seam is starting to leak. It's about one drop every 45 seconds. I'm thinking JB Weld will fix it.