EDW2020F00BB General Electric Dishwasher - Instructions

This was one of the easiest fixes i have ever done. All you need is a screwdriver. the hardest part about it was unscrewing the old spray arm. I found it was easiest to break the tabs on the old spray arm and pull out the spray tower, leaving the bottom part in. The bottom is the part to unscrew. I then put the metal end of the screwdriver through the two holes where the tabs were and used the screwdriver as a handle to unscrew it. Once it was taken out, I screwed the new spray arm in - buy hand -. You can feel it lock when it is all the way in.

First I removed the dishwasher from under the counter. I turned it onto it's side so I had access to the motor and pump underneath. I determined which version of the old pump I had. I removed the old part and easily installed the new motor/pump following the directions. It took a little while for the water to begin flowing when I started it back up. Eventually it did get going.

The repair was really easy. I ordered the part needed after looking at this website. I figured out the problem by looking into the forums. I ordered the part. It came within several days. I got home from work and after dinner pulled the dishwasher from under the kitchen counter. It was easy to do. I flipped the dishwasher on its side. Then removed the old part. It had a water inlet that required a fitting to be loosened with a wrench. It also had a flexible water fill that was attached with a cable clamp. (Remember to turn your water supply off first!) The wiring was disconnected by a simple harness. Four bolts had to be removed to pull the part off of the dishwasher body.

Installation was the reverse of this process. Have been using for a week now and the problem is corrected. Doing business with Parts Select is awesome. I know that over the last several years I have saved tons of money and learned that I can fix nearly any appliance by viewing this website.

First make sure the dishwaher is off and secure to work on: remove the lower basket, turn the broken spray arm assy counter clockwise, it may be tight, but no tool be need it, screw it all way out, remove it and replace it with your new one by turning clockwise,make sure its tight, no tools need it but basket in place and the dishwasher is ready to go

Heard a noise in our dishwasher and ended up taking the entire pump and housing out and found a small sucker stick in the impeller along with a bunch of string and other material that needed to be cleaned out. Also found that the housing was leaking at the shaft that goes to the solenoid and dripping on the solenoid and had rusted the metal plunger that goes into the solenoid. Bought the housing and solenoid unit. 1 screw (bottom one) on the housing was rusted becaue of the water. Had to hacksaw the housing and then had to drill out that screw. Also, the pump housing screen is left hand thread and is tough to get out. Had to hacksaw that too. Be careful of the orientation of the metal ring in the impeller area. I did that backwards the first time and the motor would not move. Also, the electrical connector to the motor appears to be polarized so it can only go on 1 way-notice before you take it out. Be sure to screw the solenoid bracket back on tight and notice the spring orientation before you remove-the new one was different than the old. Bottom line is that it works fine, and for $40, it's fixed, rather than spending $800 for a new one.

I only had to remove the inside door panel then the bad control panel , a total of 10 screws, and then plug in the 3 harnesss wires. FIred it up and worked like a champ!

I found that the supplied part did not have threads to receive the bolts that were used in the original part. I had to locate thin nuts and bolts and very awkwardly fit those in behind the part. The orignal part would have just bolted on from the front. I almost returned the part as unsatifactory, but decided to make do. Otherwise it would have been a 10 min job.

I pulled the dishwasher out and detached the drain hose. I attached the new drain hose after cleaning out the connection to the garbage disposal.

Now my dishwasher doesn't stink anymore!

It is pretty easy to replace the parts because the new and old parts are identical. I unplugged wire connection, removed the two screws and one small metal piece that fixes the plastic moving part, then put back with new parts.
A little bit extra time may needed due to small space in that location, also the small or flexable screw driver is needed.

Pulled unit out from counter (never had dishwasher issues before) to see if there was anything obvious with wiring or anything. Noticed that some little piece on the bottom looked to have melted (later discovered to be the drain solenoid). Removed the obviously defective part and looked it up on line. Found the name of it on Part Select's website then started shopping for best price. Came back to Part Select because the price was the cheapest I could find. Two - Three days later received part and put it back on and had the dishwasher back in place and in use within about 10-15 minutes. Marking my first ever dishwasher repair. :)

Just took the old rusty rack out and put the new one in its place.

Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.

My son found a water leak and cut the water supply off. He then pulled the machine from under the counter at which time I examined the valve under pressure and saw the leak. We cut the water off again and after tripping the circuit breaker we pulled the electrical connector and undid the mounting bracket which made getting the lines off the valve much simpler. New valve in hand I attached the lines and did a test then remounted the bracket and attached the electric. Easy as pie!

At first I found some water on my hardwood floor by the dishwasher, I thought that I might spilled't the day before, then it hapened again, so I remover the front lower cover for the dishwasher and I found water under the dishwasher, then I turned on the machine and I found a pin hall water leak from the water inlet valve. I turned the machine off, then I closed the water valve under the sink, then I disconected the power plug from the valve, the diconected the water supply copper pipe, then diconected the house from the valve to dishwasher, then got the part# from the valve sticker and the model# for the dishwasher from inside of the door. after that I went online and I got the valve. make sure to try more than one website because they all have differant prices, and Parts Select was the lowest one.

Research the problem on the internet .People suggestion was to replace the sequence switch . If this does not work replace the mother board .The sequence switch was replaced and fixed the problem .