GSD2030F02WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lewellyn from Clarkston, WA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
No water fill to dishwasher.
Replaced the water-fill solenoid valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Bayside, NY
- Parts Used:
- WD08X10057
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Small leak at the bottom of dishwasher
Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bay Village, OH
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
water inlet valve stuck open (frozen??)
after watching related video on partselect.com, diagnosis and repair couldn't have been much simpler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from chesterton, IN
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
water inlet valve wore out would not work
got replacement valve from part select and works like new this dish wash er is 24 years old. believe it or not did the job with pair of pliers and screw driver. used pliers to take off clamp and screw driver to take out 2 screws and replaced the valve the same way in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Port St. Lucie, FL
- Parts Used:
- WD09X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob just rotated on the timer shaft.
Pull the knob off and look for any special characteristics e.g. location of detents or other devices to index the knob n the shaft. Found an indentical part on on PARTSELECT website. Pictures were sure a big help. Purchased unit and installed in about 3 minutes. NO PROBLEMS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Nespelem, WA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Wouldn't clean upper rack, not enough water
Checked the water supply to the inlet valve - OK, pulled the filler hose from the outlet side of the valve and checked flow in wash cycle. Results, less than 1/2 gallon. Checked your website, found 94% sucess rate by replacing the valve, so I ordered one. It took about 10 minutes to install with a nut driver, 6" adjustable to connect water supply, and plier to hold outlet clamp open to install it; now we look forward to dirty dishes rather than dumping water into the machine it takes care of itself and we once again get sparkly cups andglasses of the top rack. OU- Rah!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Corvallis, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid fill cap broke off at base
I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bradenton, FL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes cloudy, spotting
Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy from moreno valley, CA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
dishwasher would not fill with water
Researched problems on internet,based on info ordered part. Got it in 24 hrs.followed package directions. So easy and for less than a service call! Runs like a charm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Mechanicville, NY
- Parts Used:
- WD19X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Pump was leaking from the shaft seal
Removed and inverted the DW. Removed the impeller, grinder, screen and seals then the actual shaft seal. Replaced with new parts in reverse order. Instructions provided with the seal kit were simple and excellent. They were right to the point.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from bend, OR
- Parts Used:
- WD21X10060
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
dishwasher does not drain
Key symptom: when the drain phase begins, there should be a satisfying "Thunk" from the solenoid. No Thunk=solenoid not working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Lake Bluff, IL
- Parts Used:
- WD19X10032
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher leaked badly when running
At first, I found a metal band that was rusted and loose, replaced it but still had a leak. I went to the diagnosis section and identified another area of problem, ordered the part and got super quick delivery. With the help my wife I was able to pull apart, repair and get the unit to run and stay dry. Wife is happy because she loves the décor of our old but now dry dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from Rockford, IL
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set, Wrench set
Dishwasher was left outside and the water inlet valve froze
We we're installing a used dishwasher,had to take it back out and replace the water inlet valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Kalamazoo, MI
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Valve failed and washer overflowed.
Immediately shut off water supply to the washer. After ordering and receipt ot part: Removed base panel, turned off power, disconnected wire, water supply line and screws attaching washer to kitchen counter. Pulled the washer out and turned it on its side with the valve on top. Removed and replaced the valve, returned the washer to the upright position, pushed it back under the counter, reconnected all services, screws to counter and base panel, turned on the water and power. Took two hours since I needed take a trip to the hardware store to replace a right angle water fitting .
Was this instruction helpful to you?
Thank you for voting!