GSC3400Z03BL General Electric Dishwasher - Instructions

Loosened the clamps connecting the pump, disconnected all electric and stabilizer arm. Simply unscrewed the solenoid bracket and replaced with new part.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

Your site is great! Saved me a service call for a repairman to come out and tell me what was wrong, order parts and then come back. Total repair was less than $90 including parts and shipping. It arrived in two days from when I ordered it. I ordered the replacement door gasket, the gasket insert and a new checkvalve. This was a super easy fix and I am a girl too boot! I am proud of myself!

I used a phillips screwdriver to take off about 8 screws off the white inner door fascia in order to replace the door seal. Keep this panel upright and do not lay it down since the rinse agent will leak out all over! Found out that the hard way.

Removed the old, dried out, outer door gasket, centered the notch that was on the new gasket at the top of the door and installed it all the way around in the door gasket groove. Installed the gasket insert at the bottom where the door gasket comes together on the bottom of the door.

After that was completed I used a 1/4" nutdriver to remove the 4 hex screws at the back of the dishwasher for the cover that is over the check valve. It is white and has a very fine mesh screen.. so easy to identify.

The old check valve was filled with crud and and the rubber was deteriorated. I just backed the old one out counterclockwise and put in the new one, a little better than finger tight. Replaced the cover and the hex screws with the 1/4" nutdriver.

Reinstalled the white inner door panel, insure the door handle comes through the hole in the front prior to attaching your screws back in place. Closed the dishwasher. Ran it on rinse/hold cycle to make sure no leaks before going for a full wash. Works great and drains now too.

Your site is a lifesaver! Thanks!!!

Followed the simple instructions to unscrew the old unit and replace with the new one. The unit was easily located on a diagram on the internet and the website instructions for removal were spot on.

removed screen at back of dishwasher from the inside. Twisted piston & nut assembly out by hand and replaced with new one. Very, very simple. Dishwasher works perfectly now.

I Just Open Door And Put Fill Cap In And Turn That It

First let me say, it's so easy even a caveman can do it. I removed the water out of the bottom. Then I removed the cover in the very back of the machine with a wrench. As soon as I did that, I could see the piston. Next, I twisted the white piston out with my fingers (this was the hardest part). I could see the piston had partially disintigrated. I ordered a new one, had it delivered in a few days, and put it all back in reverse. It took minutes. Thanks to the guy that posted his story, I was able to fix mine for $18.

First I opened the dishwasher and removed the lower basket. Next I removed the 4 screws that hold the food filter plate in place at the back of the tub. Then I unscrewed the Piston/Check Valve assembly counterclockwise, located at the back center of the tub, by hand. I replaced the old part with the new one and reinstalled the filter plate. I ran a rinse cycle to verify that that all of the water was purged. Finally, I reinstalled the lower basket and resumed using my dishwasher.

A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.

The repair could not have been more easy! We simply unscrewed the broken spray arm and screwed in the new one. For less than $50, we fixed it ourselves. We would have paid in excess of $350 for the repairman to fix it. We could not be more happy with this website, the videos and the fast delivery!

As per instructions from this site I simply unscrewed the entire assembly and installed the new spray arm assembly. The old unit was a bit stubborn due to age so I used the long handle of my favorite screwdriver, inserted through the bottom area, for leverage. The entire process took less than 5 minutes. Very simple and as a side benefit, the dishwasher operates much quieter than before the old spray arm broke. Guess the old arm was also worn out before it broke on this 18 year dishwasher.

Unscrewed bottom of spray arm support assembly counterclockwise by hand for removal. Inserted new part and screwed it in clockwise by hand for installation. Worked perfectly. Video was helpful.

Removed filter/screen by unscrewing 2 screws with a nut driver and then unscrewed the old Piston and Nut assembly and simply screwed in the new part. Problem solved and my dishes are much cleaner and the water is draining out completely. Easy fix for this frustrating problem.

First I removed the bottom dishwasher rack. Using a 1/4" nutdriver I removed (4) 1/4" screws from the drain cover that is inside the dishwasher all the way in the back. This will allow you to get to the piston and nut assembly which was easily removed with no tools by simply grasping and unscrewing. Used a wash cloth to wipe "gunk" from around the threads. I then screwed the new piston and nut assembly in place. Used no tools to tighten, just "snug up" by hand. The seal on my old piston and nut assembly was 50 percent gone, not sealing at all. I guess the years had taken their toll. This solved my problem. The dishwasher washes and drains as it should. Super easy fix. Took me about 10 minutes to do the repair.

Removed filter screen with the socket set, removed the piston and nut assembly with pliers, and installed the new piston and nut assembly. Put filter screen back in with hex head screws. During the process, I opened the float regulator and cleaned it out too. Water backup problems solved.