GSD3715D01AA General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eric from Mayetta, KS
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water not draining.
Removed the 4 screws on front inspection plate and had easy access to solenoid switch. Unplugged unit and switched out with repair kit. So easy a caveman could do it...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- forrest from stuart, FL
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace door gasket
from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from tampa, FL
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
water left in dishwasher after wash
Open door, remove lower wash rack, remove 4 screws holding screen in rear of inside tub with 1/4 inch socket. Unscrew piston and nut assy for checkvalve, sounds like a mouthful but it is only 1 part. Checkvalve has 2 small ears on it which allow you to twist it out, it has treads on it. Flapper on check valve flapper rots away and water pumps back into tub instead of being routed to drain line to garbage disposal. Part with shipping was just over $20.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from florida, MI
- Parts Used:
- WD21X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher did'nt drain water . solinoid was melted and stuck
First I removed the two screws that hold the solinoid in place,then I removed the e clip and unpluged the wire and pulled out the plastic lever with the solinoid and springs. To install Solinoid:First I bolted on the bracket ,then I hooked in the spring in the plastic lever and installed lever on shaft then I hooked in the long spring to the bracket small hole in the bottum then I installed the e clip next I pluged in the wire.Then I tried the Washer .Averthing works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Isleton, CA
- Parts Used:
- WD24X10015
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaking small hose.
At first I thought I would call a repair man.Then I thought-that will be at least $100!So we went online and found the part.Took about four days to arrive.I pulled the dishwasher out and turned it on it's front.The little leaking hose was easy to remove,two clamps,and the new one installed.Total cost-$14.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from wellington, FL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Dishwasher would not drain
Ordered motor and pump and replaced. Motor pump kit also comes with a drain solinoid so if that was the problem the kit repaired it. One issue is the size of the hanger to ensure the pump does not just hang on its mount. The directions were not very clear and after some trial and error I got it to work to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Buddy from Danville, IL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Pump seal was leaking
I disconnected the power shut off water supply. I then removed the drain hoses and water supply to the old pump. I removed the ground wire and the mounting rod to the old pump. Once removed, I followed the easy illustrated diagrams and instructions that came with the replacement pump.
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.
I would use this service again if needed for additonal home appliances.
Thank you
Mr. Buddy King
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.
I would use this service again if needed for additonal home appliances.
Thank you
Mr. Buddy King
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberto from Key Biscayne, FL
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water would not drain out and keep filling up sprayers work
Your video doesn't include disconnecting water supply disconnecting electrical and disconnecting drain hose but after all that the repair to change the solenoid was a easy task but the problem was not solved so I TRIED . thanks Robert
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from TUCKAHOE, NY
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Difficult to install the mounting screws
Nut driver and philips screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from FREDERICKSBRG, VA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
No water in
Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Yarmouth, ME
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Frequently get "Blocked Spray Arm" message - washer stops
Removed the 4 screws holding the filter screen assembly in the back of the tub. This exposed the Piston and Nut assembly which unscrewed fairly easily.
Replaced with the new part, put the filter screen assembly back in place ran the machine. The machine still stops with the blocked arm message - just not as frequently. The web researched fix with the piston and nut assembly replacement was obviously not the final answer. I am now out of options I believe except to bite the bullet and get a new machine. Any other suggestions are welcomed.
Replaced with the new part, put the filter screen assembly back in place ran the machine. The machine still stops with the blocked arm message - just not as frequently. The web researched fix with the piston and nut assembly replacement was obviously not the final answer. I am now out of options I believe except to bite the bullet and get a new machine. Any other suggestions are welcomed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- renee from shelby twp, MI
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench set
standing water at the bottom of the dishwasher
remove the screen at the back bottom of dishwaser. (4 screws). Unthread piston and and nut assembly for check valve....thread in new one.
Problem solved....no more water $10 part....no repair person !!!
Problem solved....no more water $10 part....no repair person !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DERRY, PA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable), Wrench set
Leaking at the valve
Just like the video and replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clyde from DUNCANNON, PA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
water would not pump out of machine
I looked at your web sight and saw how to repair dishwasher.
Was this instruction helpful to you?
Thank you for voting!