EDW3000G03WW General Electric Dishwasher - Instructions

The repair was really easy. I ordered the part needed after looking at this website. I figured out the problem by looking into the forums. I ordered the part. It came within several days. I got home from work and after dinner pulled the dishwasher from under the kitchen counter. It was easy to do. I flipped the dishwasher on its side. Then removed the old part. It had a water inlet that required a fitting to be loosened with a wrench. It also had a flexible water fill that was attached with a cable clamp. (Remember to turn your water supply off first!) The wiring was disconnected by a simple harness. Four bolts had to be removed to pull the part off of the dishwasher body.

Installation was the reverse of this process. Have been using for a week now and the problem is corrected. Doing business with Parts Select is awesome. I know that over the last several years I have saved tons of money and learned that I can fix nearly any appliance by viewing this website.

First make sure the dishwaher is off and secure to work on: remove the lower basket, turn the broken spray arm assy counter clockwise, it may be tight, but no tool be need it, screw it all way out, remove it and replace it with your new one by turning clockwise,make sure its tight, no tools need it but basket in place and the dishwasher is ready to go

I found that the supplied part did not have threads to receive the bolts that were used in the original part. I had to locate thin nuts and bolts and very awkwardly fit those in behind the part. The orignal part would have just bolted on from the front. I almost returned the part as unsatifactory, but decided to make do. Otherwise it would have been a 10 min job.

I pulled the dishwasher out and detached the drain hose. I attached the new drain hose after cleaning out the connection to the garbage disposal.

Now my dishwasher doesn't stink anymore!

Disconnected the electrical, water supply and drain. Pulled unit out from under counter, tipped it on its side and replaced the motor/pump unit. tipped it back on its legs put it back under the counter connected the water supply, drain and electrical. All went well. The unit performs as it should. it took about two (2) hours without rushing through it.

Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.

Just took the old rusty rack out and put the new one in its place.

My son found a water leak and cut the water supply off. He then pulled the machine from under the counter at which time I examined the valve under pressure and saw the leak. We cut the water off again and after tripping the circuit breaker we pulled the electrical connector and undid the mounting bracket which made getting the lines off the valve much simpler. New valve in hand I attached the lines and did a test then remounted the bracket and attached the electric. Easy as pie!

At first I found some water on my hardwood floor by the dishwasher, I thought that I might spilled't the day before, then it hapened again, so I remover the front lower cover for the dishwasher and I found water under the dishwasher, then I turned on the machine and I found a pin hall water leak from the water inlet valve. I turned the machine off, then I closed the water valve under the sink, then I disconected the power plug from the valve, the diconected the water supply copper pipe, then diconected the house from the valve to dishwasher, then got the part# from the valve sticker and the model# for the dishwasher from inside of the door. after that I went online and I got the valve. make sure to try more than one website because they all have differant prices, and Parts Select was the lowest one.

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

First I looked for blockage and found none.I took the pump off and hooked power to it in my work shop and it did spin when powered up.We had broken a glass in the washer and thats when the problem started. I did find a few small pieces in the check valve assembly. It did not look bad but for cheap I ordered the part. Ran the washer and it drained on the wash but not on the final. Turned off the power.Slid the wash out where I could get to the power and not unhook the water. Turning off the power I disconnected the wires and carefully turned the power on and touched them to the pump and forced it to drain knowing that the pump worked I thought it would at least empty the water. I touched the wires to the pump and the board clicked the water drained. Hooked it back up. Ran it and has been working great since.

Replaced with a new rinse aid fill cap.

Just lift out the old dishrack and put in the new. Very easy and straightforward. Easy to order, unit came assembled. Happy customer.

removed old drawer-like basket, installed the new duplicate replacement part. Easiest "repair" I've ever done!

Removed the old one from its slot and slid the new one into it.
No instructions needed.