PDW9980N00SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Randy from Placentia, CA
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Bottom dish basket would not roll in and out. Wheels were falling off.
Removed the existing stud rollers with the wheels attached. Then removed the wheels from the stud roller. Then snapped the wheels on the new "Better Designed" stud rollers. Then easily snapped the new stud roller assembly in place. Piece of cake...works like a charm.
Thanks,
Randy
Thanks,
Randy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Newport Coast, CA
- Parts Used:
- WD35X21041, WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheels were broken and had fallen off rack wouldnt roll
We received our parts for our dishwasher within 2 days. It was very simple to find the parts on your site, and very easy to install. Our dishwasher is back to normal and the racks roll in and out easily. I would recommend ordering from PartSelect to anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lakewood, NJ
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Wheels on lower basket kept falling off, axel worn out.
Removed empty basket from dishwasher. Placed basket upside down and removed remaining wheels from basket by detaching worn axel from attachment points. ie, No tools needed for this procedure. Once axel and wheels were removed, I squeezed the end of the old axel with needle nose pliers or regular pliers to relieve the outward pressure and pushed the old axel out of the wheels. Easy, popped right out.
Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel and
attached it to the basket at the original position. New axel grips the basket like a clothes pin would.
Continued and replaced all eight axels at this time.
Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.
Will definately re order again if needed. Thank You.
Positioned new axel against the outer wheeel hole and applied thumb/finger pressure to snap in new axel. Took the wheel with the new axel and
attached it to the basket at the original position. New axel grips the basket like a clothes pin would.
Continued and replaced all eight axels at this time.
Replace basket in machine, stand back and admire work and parts!!!! Parts received promptly with no hassels. Excellent company to do business with, clear photos and ordering forms.
Will definately re order again if needed. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TAMPA, FL
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rollers broken
No instructions. At first thought I needed instructions. A minute later I was attaching the new rollers. Simple and easy. Took less than 15 minutes. Would recommend these rollers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ARTHUR from OAK PARK, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Detergent dispenser did not work
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN D. from GOSHEN, IN
- Parts Used:
- WD01X10175
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
wouldn't drain
Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- C. from Lexington, KY
- Parts Used:
- WD01X10175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would only drain intermittenly
Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from KENT, WA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
valve leaked
shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Von from SanBernardino, CA
- Parts Used:
- WD35X21041, WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
all 8 wheels broken from lower rack & basket broken
went to sears and was told axles not available ! after they sold my wife all 8 wheels in two diffrent colors. started looking on line found your web site I entered my model number. In a matter of minutes I found the parts checked stock ordered them and recived conformation.
prices and shiping are fair. ordered recived and installed parts in 4 days WOW ! wished all purchases went this smooth.
Von Neal
prices and shiping are fair. ordered recived and installed parts in 4 days WOW ! wished all purchases went this smooth.
Von Neal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from Princeton, NJ
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The axxle for the wheels were worn out causing wheel to rotate inward and the tray to be to low in the dishwasher.
Simply pull out the old axle and snap in the new one. It is simple. Also the replacement axels were MUCH better quality than the originals. The bottom tray now slides in and out very easily. Note, if you have this problem, you do not need to replace the wheel, just the axle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Raleigh, NC
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheel fel off bottom tray
but axle on new wheen and put axle on tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Waunakee, WI
- Parts Used:
- WD35X21041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Wheels on lower unit kept falling off.
I simply removed the old (broken) stud rollers by pinching them with a needle nose pliers and pushing them out, snapped the new stud roller in the wheel, and snapped the wheel onto the lower basket unit. If you have all of the wheels and they are in good shape, you do not need to buy new wheels, the new stud rollers work just fine with the old wheels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ORLANDO, FL
- Parts Used:
- WD34X11158
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Touch panel was not operating
Turned off power to the dishwasher. Used Lock out Tag Out Protocol.
Removed the inside Stainless panel of dishwasher. followed the wiring from the keypad to the internal board. Disconnected the wiring to the board. Removed the keypad and wiring from board. installed new keypad assembly connecting to the internal board and then affixing the new keypad assembly to the top of the dishwasher door assembly.
Removed the inside Stainless panel of dishwasher. followed the wiring from the keypad to the internal board. Disconnected the wiring to the board. Removed the keypad and wiring from board. installed new keypad assembly connecting to the internal board and then affixing the new keypad assembly to the top of the dishwasher door assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from TYNGSBORO, MA
- Parts Used:
- WD08X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Started to have a leak
Pull out the old, died gasket. Clean out track that holds gasket. insert new gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SIMPSONVILLE, SC
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The door on dishwasher soap dispenser broke.
Repaired the soap dispenser.
Was this instruction helpful to you?
Thank you for voting!