EDW3000G03CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Doug from NEW YORK, NY
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door leakage
The instructions provided are very good if I had done before. My concern was getting the gasket to sit properly at the bottom where you cannot see. I removed the inside of the door (7 screws) and this made it easier to assure gasket sat properly in the track. may have cost an extra 15 minutes but worth it. If I do again I will take door apart again, however I think this is fixed and should not need attention again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Caseyville, IL
- Parts Used:
- WD26X10013, WD24X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water leaking onto the floor
I removed the dishwasher, removed the front kick panel, layed the dishwasher on its back, loosened the clamps and removed the old motor and pump assy. Cleaned up the area where the unit was, Installed the new unit, tightened the clamps and it was done. Probably took around an hour because of my cleaning up the sealing areas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from CLEVELAND, OH
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Leaked at bottom of door
I took the inside of door off to install both gasket and gasket insert. Much easier this way. Also it’s much easier to fish locking handle through the door if you extend the handle half way and put through opening when raising the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helmut from EAST KINGSTON, NH
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower wheels kept falling off
Installed new lower rack wheel kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Sykesville, MD
- Parts Used:
- WD28X10177
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
basket for silverware was broken
opened the box , new one was an exact fit, pulled out the old one and dropped the new one in place??, this is more of a review, the new part was the exact same one...perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Georgetown, CO
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Plastic part of inlet valve cracked
Hired my neighbor, who is a plumber.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Novato, CA
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The problem was that the dishwasher lower sliding shelve was rusting out and coroding
We ordered a new lower shelve and slid it in on the rollers and it is secure and works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from CARUTHERSVLLE, MO
- Parts Used:
- WD13X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would go on and off during operation
Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLUMBUS, GA
- Parts Used:
- WD13X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door latch broken
I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn
Thanks GE,
T. Dunn
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from EAST MEADOW, NY
- Parts Used:
- WD14X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Plastic hinge arm link broke
Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WEST DEPTFORD, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was old and leaking.
I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Terra Ceia, FL
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
The water valve went out
I took the old one off and replaced it with the new one, which fir perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Canton, GA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
The pump shaft leaked
I used the pump/motor replacement kit. It was a very easy repair and the parts were a direct replacement with no modification necessary. I saved over $300.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SOUTHPORT, NC
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken spring on door.
See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.
Was this instruction helpful to you?
Thank you for voting!