Models > GSD4010Z02AA > Instructions

GSD4010Z02AA General Electric Dishwasher - Instructions

Jump to:

All Instructions for the GSD4010Z02AA
106 - 120 of 247
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Ailton from NEWARK, NJ
Parts Used:
WD08X10016
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The gasket was parched and was going out
Very simple to change it, only follow the instructions that came with the part and don’t have how to do wrong
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
clyde from DUNCANNON, PA
Parts Used:
WD24X10018
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
water would not pump out of machine
I looked at your web sight and saw how to repair dishwasher.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brett from Sound Beach, NY
Parts Used:
WD26X10013
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Pump/Motor leaking at shaft
This was one of those wonderful repairs where anything went right.
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacement was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
kevin from longmont, CO
Parts Used:
WD26X10013
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
leak between motor and pump housing
repair kit was complete and directions were easy to follow. my model of dishwasher disnt even require any of the adapters. really only required removing a couple of clamps and replacing everything as a single unit
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bonita from Alexandria, VA
Parts Used:
WD24X10018
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
End of cycle water in bottom of nDishwasher
Removed screen bottom rear andfound a plunger type part, unscrewed plunger and found it was distressed around it and did not close of a tight seal. Placed new part into location and dishwasher now proforms perfect...
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from Hesperia, MI
Parts Used:
WD26X10013
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Leaking from the pump
Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cliff from Atlantic Beach, NC
Parts Used:
WD26X10013
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
The pump seal was leaking.
Installed new motor and pump kit. Very easy, except that the instructions did not give any detail on the electrical hook-up. The problem was that the electrical connections for the motor and solenoid were the same on the replacement kit, making it possible to switch them. Be sure and mark the connections from the old unit before removing them.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Pembroke Pines, FL
Parts Used:
WD16X10011
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Could not get the arm to close.
I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.

Thanks for your help.
4 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Warren from Glendale Heights, IL
Parts Used:
WD26X10013
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Wrench (Adjustable)
Dead spot in motor/pump seal leak
I had a problem where the GE dishwasher would randomly stall upon startup due to a dead spot in the motor which prevented it from energizing. I removed the dishwasher's bottom access panel to inspect it and found that not only was the motor dead but it had a sizable leak emanating from the pump seal. I removed the dishwasher from under the cabinet area and turned it over to make it easier to replace the motor and pump assembly which only took a matter of minutes; the most difficult part of the repair being the reinstalling of the dishwasher. The replacement motor/pump assy was not only modified from the original parts but it is also much quieter than the original. I also have to commend PartSelect on their very speedy delivery which was only 2 days. All in all with a couple of minor modifications that was taken care of with the included parts the repair went very easy.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jim from Manassas, VA
Parts Used:
WD26X10013
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
water not completely draining and dishwashing action not very effiencent
I went to your site and check all the diagrams and then read the postings from others. I turned off the electrical breaker then took off the lower cover of the dishwasher. After disconnecting the water and electricial connections I was able to remove the 2 screws holding the unit in place and it came right out. I turned the unit over and was able to just remove the old part and put the new part in place. The whole job took me about one hour but I had never worked on a dishwasher before. Your site made the repair very easy to do on my own.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Crystal Lake, IL
Parts Used:
WD26X10013
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench set
My motor froze up
Not really difficult to do. First remove the washer from the counter and flip it over. Carefully determine the correct drawing in the instructions which matches your machine. Follow insructions and double check everything. Took about an hour - and I saved about $350.00 by fixing it myself rather than buying a new one!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Orlando, FL
Parts Used:
WD21X10100
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Lights blinking, but unit would not power up. Installed part everything works great! Caution, the door lock hasto be installed on the cover before you screw it back to the door, then all is good! Lost an hour before I realized this.
Went great, but make sure you install lock for the door on the door cover, not the door and save yourself some time!
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Harry from Franklin, TN
Parts Used:
WD12X10284
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Rinse Aid Fill Cap missing from dishwasher in condo I just bought.
Opened package, removed cap and screwed it in place.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gene from Rocklin, CA
Parts Used:
WD24X10018
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Dishwasher was not draining completely
Just remove the 4 screws at the lower rear inside the washer to remove screen holder...then unscrew the Piston and Nut Assembly by hand. Put in the new unit, reattach the screen holder with the 4 screws...and the job is done. Probably takes less than 5 minutes....very easy.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff from Franklin, TN
Parts Used:
WD26X10013
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set, Wrench set
Had leak in the dishharge valve
The instructions were excellent, The repair was simple. The order process was excellent, as well as the delivertime. Part Select offers excellent bluline breakdown as well as east access to help which I did not need. Thank you Part Select for yor excellence of service.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GSD4010Z02AA
106 - 120 of 247