GSD2000Z05WH General Electric Dishwasher - Instructions

Heard a noise in our dishwasher and ended up taking the entire pump and housing out and found a small sucker stick in the impeller along with a bunch of string and other material that needed to be cleaned out. Also found that the housing was leaking at the shaft that goes to the solenoid and dripping on the solenoid and had rusted the metal plunger that goes into the solenoid. Bought the housing and solenoid unit. 1 screw (bottom one) on the housing was rusted becaue of the water. Had to hacksaw the housing and then had to drill out that screw. Also, the pump housing screen is left hand thread and is tough to get out. Had to hacksaw that too. Be careful of the orientation of the metal ring in the impeller area. I did that backwards the first time and the motor would not move. Also, the electrical connector to the motor appears to be polarized so it can only go on 1 way-notice before you take it out. Be sure to screw the solenoid bracket back on tight and notice the spring orientation before you remove-the new one was different than the old. Bottom line is that it works fine, and for $40, it's fixed, rather than spending $800 for a new one.

It is pretty easy to replace the parts because the new and old parts are identical. I unplugged wire connection, removed the two screws and one small metal piece that fixes the plastic moving part, then put back with new parts.
A little bit extra time may needed due to small space in that location, also the small or flexable screw driver is needed.

I pulled the dishwasher out and detached the drain hose. I attached the new drain hose after cleaning out the connection to the garbage disposal.

Now my dishwasher doesn't stink anymore!

Pulled unit out from counter (never had dishwasher issues before) to see if there was anything obvious with wiring or anything. Noticed that some little piece on the bottom looked to have melted (later discovered to be the drain solenoid). Removed the obviously defective part and looked it up on line. Found the name of it on Part Select's website then started shopping for best price. Came back to Part Select because the price was the cheapest I could find. Two - Three days later received part and put it back on and had the dishwasher back in place and in use within about 10-15 minutes. Marking my first ever dishwasher repair. :)

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

replaced solenoid. worked properly after repair

Replaced with a new rinse aid fill cap.

Removed the old one from its slot and slid the new one into it.
No instructions needed.

Unplugged unit, unscrewed screws on top of dishwasher attached to countertop, undid water supply and drain hose that goes into tee with garbage disposal. Using crescent wrench turned front leveling screws up all the way and slid/rocked dishwasher out from under the counter - I had no problem leaving back leveling screws down. Turned dishwasher over on some towels (it WILL leak some water so spread out some towels!) so it was oriented like the directions that came with pump and motor. The directions were good, although color or a picture might have been more helpful. CHECK the new pump/ motor unit CAREFULLY for any loose debris from packing etc. I had a small piece of plastic that was in the top of the motor that goes in the dishwasher bottom that rattled around after I installed everything and put it back. I was able to get to it from the drain assembly in the tub but it made a heck of a racket at first. All in all, I had a great experience. I'm glad I ordered the pump and motor even though I only thought I needed the drain solenoid because when I took the old unit out, the prop on the old impeller was almost gone. Easy to order, good customer service (I called with a question and talked to a wonderful customer service representative!), good directions and easy to do. I'd say a 4 out of 10 in terms of difficulty. Thanks PartSelect!

Only getting "humming" sound from dishwasher. Although water had filled the dishwasher tub, pump/motor would not operate. After some research, figured the motor had siezed and I had to replace the pump/motor assembly as mentioned on this site. The kit came in a couple days and I reserved a Sunday afternoon for the repair which I had never done before. Hardest part of repair was unhooking and removing dishwasher from under counter and then getting it back in proper place. I would suggest providing some instruction within the repair instructions showing how the dishwasher is installed or how to remove it as I had never installed one so I was not quite sure what screws etc I needed to remove on the dishwasher itself to start to remove it? I was able to find the original installation instruction for the dishwasher and found that all you had to do was remove two screws from the inside top of the dishwasher which were securing it to the bottom side of the kitchen counter and then the whole thing just slides out. Once removed, turned dishwasher over to access bottom where pump/motor is located. After determining which diagram to use with the instructions, proceeded to replace the motor/pump assembly. It came out easily after wrestling with some corroded bolts/nuts and the existing pump inlet and outlet hose clamps. Mine were old and worthless and no new ones (3-4") are supplied with the kit. Had to run to hardware store to get new hose clamps for the inlet/outlet of the pump before intalling new one. Suggest new hose clamps be provided with the kit. Only thing that was not too clear in instructions was when reconnecting power wiring harness to motor. By looking closely at the instruction diagram I was able to locate what looked to be the right power extension harness from the bag of parts and attach it to the existing power wire harness and the new motor. Suggest also that you somehow better distinguish or identify the proper way the power wire harness should be fastned to the motor? The existing power wires were both the same color and both the female and male connections for the power at the new motor were identical leaving you to guess which wire goes to which connection. After re-installing dishwasher, put about a gallon of water in bottom of unit prior to starting and then put it through a few cycles. It has been working just like new. Suggest having a helper when removing and re-installing dishwasher from under kitchen counter to assist with the power cord, water line, drain line, and help to turn the dishwasher upside down and right side up again.

The Solenoid black plastic had melted around the solenoid shaft. I unplugged the solenoid, removed 2 screws,then one C clip and pulled the the unit out. The new solenoid is difficult to install all together as the shaft it goes on holds it all together when both springs are installed - - so I installed in one piece, with the 2 screws, except for the white plastic thing, the C clip that holds it on the shaft, and one of the two springs - - these three items went on separately. I wanted to thank the help your expert gave, but I couldn't figure how to do that.

First I opened the package and screwed the new dispenser cap into place.

Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.