GSD2020F01BB General Electric Dishwasher - Instructions

Used drill and easy out to remove broken part, then put in new one

Identified solinoid responsible for the operation of the drain flapper valve had become damaged, possibly due to its coil shorting and overheating, the inside plastic insulation then melted and came up through the solinoid pin hole. I removed the tension spring holding the flapper drain valve shut, removed the eclip holding the white phenelic arm connected to the tension spring, removed the two screws mounting the solinoid assy. I threw out the bad solinoid. I then proceeded to install the replacement solinoid in reverse order of removal. The end. Works like a champ ! Thank you for your quick shipping response time. My wife is now once again happy. As you know, if my wife isnt happy, I sure wont be happy. :)

Opened package, removed cap and screwed it in place.

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

problem solved..thanks

The repair wouldn't have taken as long as it did if the pictures on the installation sheet were clearer. They were very smudgy. Couldn't see the details on the pictures.

I took the bottom plate off by removing 1 screw on each side. I then pulled the water inlet valve out, disconnected the 2 wires. Because mine was the original inlet valve and GE changed the new one I had to remove the new inlet valve from the face plated and use the old face plate. I then reveresed everything and put it back together and Wah Lah the dishwaher was fixed!!

Dishwasher was not filling with water so I assumed the Water Inlet Valve was the problem. I replace the valve but still had the same problem. Studying everything I noticed another problem. The Drain Solenoid which I had replaced 9 months earlier was closed. The plunger was in the down position but must be in up position while washer is filling.
Water was pumped out as soon as it came in. I removed the Drain Solenoid and found the plunger securly stuck inside the plastic cylinder. I forcefully removed it. I knew the solenoid was probably OK because it jerked during the drain cycle. I put emery cloth around a dowel rod and sanded inside the plastic cylinder until plunger moved freely. I smoothed inside with wet or dry sandpaper. After re-installing the solenoid the dishwasher works great. My only explanation is the solenoid has a design flaw and that heat from the solinoid must expand the plastic inward over time.

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.

The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.

The dishwasher runs quieter and the dishes come out clean now.

Originally replaced solenoid without pulling unit out, but continued to leak. Purchased the entire motor and pump kit; pulled unit out, turned it on end and replaced the motor. The only problem was that no new ground screw was sent with the kit and the existing screw wasn't quite short enough to connect. Either the hole on the replacement kit needs to be deeper or a bond screw needs to be sent that will fit the new kit. We had to find our own screw that would fit properly.

followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which was not present on my original however it installed perfectly and no longer leaks.

Piece of cake. All done and working just fine.

I removed the old valve with wrench and Philips screw driver.Unscrewed the mounting plate and water hose. When I went to replace the new water inlet valve, I found that there was a mismatch on the screw holes for the new mounting plate. Different screw threads. I tried to find screws that would fit, but didn't have any.So I manged to make the old screws re-thread themselves and hold the plate in place. I then attached the water hose and started the dishwasher up. Make sure to power off the unit then power it back on to clear and reset the programming. Works great now.

pulled washer out and turned it upside down to get to the pump&motor.
no problem to fix