GHD6711N10WW General Electric Dishwasher - Instructions

In order to access the fill valve, dishwasher had to be removed from under countertop. Disconnected water supply line and drain hose under sink. Unplugged unit and removed 2 screws holding unit to countertop. I was then able to pull unit out and replace valve. After reinstallation, the same problem existed. Further research pointed to the control module, approx. $100.00 or the motor, approx. $250.00 - $300.00. I than began looking at new dishwashers, but I did email GE with the problem. They suggested I use citric acid or vinegar in hot water, pour into right rear portion of tub and wait 1/2 hour. After doing that, the dishwasher worked perfectly.

I noticed the circulation pump was not operating. If I turned the motor with a screw driver it would start running. I replaced the pump and now the dishwasher works like new. Very easy to replace the pump but you will have to pull out the dishwasher and turn on its back. I was able to confirm the circulation pump was the problem by observing the motor not running when it should but it would run once I turned the inside motor parts(be careful!). I also had to replace the center sprayer which again was very easy.

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.

We pulled the dishwasher out completely, drained water that was in the dishwasher. Tilted the dishwasher and the part we needed to replace (Pump Drain Assembly) was in clear view. We used a screwdriver to take out a few screws and replaced the Pump Drain Assembly with the new one. Put the dishwasher back in and proceeded to wash dishes in the now fixed dishwasher. The part was very easy to change out.

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

The connector pump had a pinhole leak at the seam (new part did not have seams). Also replaced the sump inlet which looked worn and the impeller.

Lay dishwasher on it's back to access the bottom. Loosen all clamps. Remove both U shaped holders on the sump inlet. Remove screws holding the drain motor. Pull out the pump motor and sump inlet. Connector pump can be unscrewed from the bottom.

Replace parts and reassemble. It isn't that bad once you start disassembly, especially for anyone somewhat handy.

Just took out the old rack and replaced it with the new one.

Traced the problem back to the water valve. turned off the water. Disconnected the water inlet and outlet lines. removed the 2 mounting screws and unplugged the terminals.

My dishwasher was doing a terrible job of cleaning. It was leaving food on dishes, and wasn't dissolving all the detergent. I replaced all the spray arms and the filter, as they seemed clogged, and god knows how old. It's a super easy repair, and the dishwasher now works as if it were brand new.

Turned power off, removed dishwasher, tipped on side, removed and installed pump asym, reinstalled

Just replaced the part

I removed the screws on the inside of the door assembly, which allows the inside of the door to seperate from the outside. The escuchen (control panel) was easy to remove - the handle actuator is inside the control panel. The handle assembly was easy to take apart and re-assemble with the new handle and spring. I then inserted the control panel back into the outside door and reattached all of the screws with a power drill. This was a repair that a GE-authorized service tech told me was going to be over $540 - he claimed the control panel and door handle/actuator was a single assembly. In the end this repair cost me $14 in parts and 15 minutes of time. I complained to GE Consumer Affairs and they rebated the tech house call back to me in 5 business days.

This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!

Ordered your new and improved interlock cover made with better plastic (thank you). Your new spring is also better. It's bigger and longer and is now the right size. (Thank you). Your parts are better than oem. The interlock is easy to get to. The oem one is black and you can see that it is bulged. The replacement one is gray speckled with white and black. You can see the improvement by just making a comparison. Just unclip the old one and clip in the new one. . Repace panel cover. Now it works and should work now for many a year. Thanks! Parts select.