GHD5015F00AA General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- edward from noblesville, IN
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack was rusty
Took out the old one and put in the new one! Note the delivery time was great! The part was ordered one day and delivered the next! Thank You Ed Andrews
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Anthem, AZ
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
new bottom dishwasher rack
it was super easy and the part came in days. it was super quick
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandy from Port Hueneme, CA
- Parts Used:
- WD21X10100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Blinking Light
Repair was very easy Disconnected power source. Removed screws on panel. removed 2 screws holding switch assembly. removed plugs and placed in new switch removed old switch and replaced. replaced screws check for function before replacing panel no problems Thanks for the help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from TROY, OH
- Parts Used:
- WD24X10018, WD22X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
There was water remaining in the bottom after a wash cycle
and there was not supposed to be so I checked the drain and it was clean and I found a part in the back that looked like it was damaged from use and it was so I got a new part and changed it and that fixed the problem. I removed the screen from the bottom rear inside the cabinet that covers the nut and piston and I changed the part and that fixed the problem . Now no water stays in the bottom when the cycle is done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Millerton, NY
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Leaking door
My husband said it was easy. But the gasket didn't solve the problem. So we had to order another part. We had to order the little black stoppers that go in the hinge area. Still leaked so my husband took them back out and cleaned the area. Then put some kind of sealant in and replaced the black robber things. So far that worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Georgetown, CO
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Plastic part of inlet valve cracked
Hired my neighbor, who is a plumber.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Novato, CA
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The problem was that the dishwasher lower sliding shelve was rusting out and coroding
We ordered a new lower shelve and slid it in on the rollers and it is secure and works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from CARUTHERSVLLE, MO
- Parts Used:
- WD13X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would go on and off during operation
Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Sykesville, MD
- Parts Used:
- WD28X10177
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
basket for silverware was broken
opened the box , new one was an exact fit, pulled out the old one and dropped the new one in place??, this is more of a review, the new part was the exact same one...perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from CLEVELAND, OH
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Leaked at bottom of door
I took the inside of door off to install both gasket and gasket insert. Much easier this way. Also it’s much easier to fish locking handle through the door if you extend the handle half way and put through opening when raising the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WEST DEPTFORD, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was old and leaking.
I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neal from STATESBORO, GA
- Parts Used:
- WD08X10057, WD08X10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher was leaking
I took the inside door off as shown in the gasket insert video and it made much easier to clean and insert the door gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLUMBUS, GA
- Parts Used:
- WD13X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door latch broken
I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn
Thanks GE,
T. Dunn
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Caseyville, IL
- Parts Used:
- WD26X10013, WD24X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water leaking onto the floor
I removed the dishwasher, removed the front kick panel, layed the dishwasher on its back, loosened the clamps and removed the old motor and pump assy. Cleaned up the area where the unit was, Installed the new unit, tightened the clamps and it was done. Probably took around an hour because of my cleaning up the sealing areas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Hooks Town, PA
- Parts Used:
- WD28X10103
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
upper spray would fall off
Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.
Thank You
Debbie Bradford
Hookstown, Pa.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.
Thank You
Debbie Bradford
Hookstown, Pa.
Was this instruction helpful to you?
Thank you for voting!