GSD2000G00BB General Electric Dishwasher - Instructions

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!

I went to your site and check all the diagrams and then read the postings from others. I turned off the electrical breaker then took off the lower cover of the dishwasher. After disconnecting the water and electricial connections I was able to remove the 2 screws holding the unit in place and it came right out. I turned the unit over and was able to just remove the old part and put the new part in place. The whole job took me about one hour but I had never worked on a dishwasher before. Your site made the repair very easy to do on my own.

Disconnected water, drain, electrical- remove dishwasher.
Place dishwasher on back removed part- replace with new part-reconnected and reinstalled.

The repair wouldn't have taken as long as it did if the pictures on the installation sheet were clearer. They were very smudgy. Couldn't see the details on the pictures.

I took the bottom plate off by removing 1 screw on each side. I then pulled the water inlet valve out, disconnected the 2 wires. Because mine was the original inlet valve and GE changed the new one I had to remove the new inlet valve from the face plated and use the old face plate. I then reveresed everything and put it back together and Wah Lah the dishwaher was fixed!!

problem solved..thanks

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.

The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.

The dishwasher runs quieter and the dishes come out clean now.

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

Dishwasher was not filling with water so I assumed the Water Inlet Valve was the problem. I replace the valve but still had the same problem. Studying everything I noticed another problem. The Drain Solenoid which I had replaced 9 months earlier was closed. The plunger was in the down position but must be in up position while washer is filling.
Water was pumped out as soon as it came in. I removed the Drain Solenoid and found the plunger securly stuck inside the plastic cylinder. I forcefully removed it. I knew the solenoid was probably OK because it jerked during the drain cycle. I put emery cloth around a dowel rod and sanded inside the plastic cylinder until plunger moved freely. I smoothed inside with wet or dry sandpaper. After re-installing the solenoid the dishwasher works great. My only explanation is the solenoid has a design flaw and that heat from the solinoid must expand the plastic inward over time.

Originally replaced solenoid without pulling unit out, but continued to leak. Purchased the entire motor and pump kit; pulled unit out, turned it on end and replaced the motor. The only problem was that no new ground screw was sent with the kit and the existing screw wasn't quite short enough to connect. Either the hole on the replacement kit needs to be deeper or a bond screw needs to be sent that will fit the new kit. We had to find our own screw that would fit properly.

All new seals

Turned off breaker. Turned off water and disconnected water line to make it easy to pull unit out and turn on it's side. Once that was done it was an easy swap out. Exact same motor/pump assembly. Love this site. Thanks

I replaced the entire Water Inlet Valve. The part was perfect and fixed the problem. The only difficulty was the brass elbow connection that connects to the incoming water line had plumbing putting that connected it to the old Water Inlet Valve. I had to get a couple of large adjustable wrenches to take it off. I needed it as I didn't want to buy another one. I was thankful that I had some extra plumbing putty on hand to seal the threads when I put the brass elbow back on the new Water Inlet Valve. That saved me a trip to the hardware story. All in all, I'm very pleased that I was able to fix this myself. I'm not exactly a Mr. Fixit, so this was a good experience.

Thank you for having the parts displayed as you did. It was easy to find-select-buy. Delivery was fast and repair was easy. Thanks Marianne