ZBD3500Z00WW General Electric Dishwasher - Instructions

Order new part. Lightning fast delivery. Unscrew old one, put in new. 30 seconds. Don't get any easier.

simply snap new one in place. I will have to say your service was fantastic. I received the new cap 2nd day. I am very pleased and would not hesitate to order something else if needed.

followed the excellent instructions accompanying the gasket.

I unscrewed the lower spray arm and support assembly and then screwed the new part in. Very easy.

go to google..replace ge dishwasher rack.. very clear way to pry tab with a quarter and rotate end cap.. remove/replace rack reverse install end cap

Grab the large portion of the assembly and unscrew it- if you've got hard water, this may take some serious effort. Screw in the new part, and your good to go!

Removed old gasket, cleaned grooves, installed new gasket

Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

The original part number was no longer available, but Parts Select was the only repair part service that seemed to have a replacement. open the dishwasher door and removed five screws on interior panel. Remove panel to expose control board and remove miniature connecting plugs. Remove three screws to release control panel. Replace new control panel in reverse order. The locking handle was only slightly tricky to get in position at the same time as getting interior panel in position; four hands may be better than two. Maybe a twenty or thirty minute job, i didn't time it. Of you own a phillips screwdriver it is a no-brainer.

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!

Followed easy instructions and completed repair in less than 30 minutes.

Too easy- what made it easier was this is a portable roll-around unit I could lay on it's back. Loosen the two clamps around the washer pump, hook up the drain solenoid, washer motor wires, attach the motor hanger, that's basically it. It took longer to make sure I was working from the right set of instructions- this pump covers several models. Once I had that right, it was really a snap. Now the unit is so quiet. It once sounded like a jet engine in the kitchen, now it runs so quiet you can hear the water splashing around inside- a big improvement. We should be able to hang onto this thing for a while longer.

Take out the screws in the side of the door (~7) and pull the two door sections apart at the top. I suggest that you tape the door latch in place since it can slide out; it can be difficult to replace. Use a short stem screw driver to take out the three screws holding the sequence switch in place, and unplug the two sets of wires. Once this is completed, the sequence switch will slide out. Reversing these steps completes the installation.

Instead of purchasing a new dishwasher, I elected to replace the motor/pump assembly which the existing was noisy and leaking water. To start to took pictures of the existing assembly and marked the wiring connections. I read the instructions a few times until I fully understood and had the necessary parts identified. The only problem was the bracket that holds the solenoid has two holes for mounting the drain feedback bracket were not threaded. I was able to tap the holes (metric) and mount the bracket. Caution must taken not damage the solenoid coil.