GSD5650D01CC General Electric Dishwasher - Instructions

Removed screws on the drain pump filter screens at the back of the dishwasher, unscrewed the check valve, screwed in the replacement unit, and re-affixed the filter screens.

I lived with the drain problem for 6 months and reviewed on line trouble shooting which all pointed me to a pump or solenoid valve problem. I pulled the unit and disassembled everything before noticing that the rubber washer/stopper at the top of the check valve had erroded away and was not preventing water from pumping back into the cabinet when the drain pump kicked on. Always check the condition of this check valve first if you dishwasher is not draining properly. It was so easy once I found the bad part.

The dishwasher was in a rental so I didn't want to spend the money for a new one. The part was expensive compared to a new (cheap) dishwasher. The order was shipped promptly and arrived when I expected even though it was Christmas time. The part fit perfectly and everything is back in place.

As suggested. Pull washer, remove screws from top and replace with new part. Very simple and easy if you follow steps furnished by this site.

We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.

Put new basket in, threw old one away

and there was not supposed to be so I checked the drain and it was clean and I found a part in the back that looked like it was damaged from use and it was so I got a new part and changed it and that fixed the problem. I removed the screen from the bottom rear inside the cabinet that covers the nut and piston and I changed the part and that fixed the problem . Now no water stays in the bottom when the cycle is done.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

We ordered the pump kit by model number and it was a perfect match.(It was on our door step in 2 days with normal shipping!) Three bolts and a couple of electrical connections later and the pump was off The install was just as easy. The instructions were very easy to follow.It's great to find a company these days that knows what it is doing and does exactly what it says it will do.
Kudos and thanks!

My husband said it was easy. But the gasket didn't solve the problem. So we had to order another part. We had to order the little black stoppers that go in the hinge area. Still leaked so my husband took them back out and cleaned the area. Then put some kind of sealant in and replaced the black robber things. So far that worked.

Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.

Thank You
Debbie Bradford
Hookstown, Pa.

I removed the dishwasher, removed the front kick panel, layed the dishwasher on its back, loosened the clamps and removed the old motor and pump assy. Cleaned up the area where the unit was, Installed the new unit, tightened the clamps and it was done. Probably took around an hour because of my cleaning up the sealing areas.

Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.

First of all this site is awesome. So helpful in diagnosing and ordering the part. I highly recommend!

So, the solenoid was melted and needed to be replaced. If you're looking from the front of the dishwasher it's on the left side and it has 2 screws and a c ring. I couldn't get the c ring back on, but the piece stays on without it. Works fine now.

The sump was very clogged with caulk like crud that we think was a chemical reaction from soap that was used the first two years. When I first started troubleshooting, the sump seemed to be the problem, so I replaced that. There was a small hose on the sump that was broken so it made sense to replace it anyhow.

When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.

I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.

Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.

My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.

TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.

Repaired by watching the video provided on my computer by this site . This video was a life saver and covered every detail. My thanks to this site !!!