GSC3200Z01BL General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Merwyn from Lima, OH
- Parts Used:
- WD28X10007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
tower cap broke
simply snap new one in place. I will have to say your service was fantastic. I received the new cap 2nd day. I am very pleased and would not hesitate to order something else if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loring from Cambridge, MA
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket deteriorated
followed the excellent instructions accompanying the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Yucca Valley, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The smallest portion of the sprayer had been broken
Grab the large portion of the assembly and unscrew it- if you've got hard water, this may take some serious effort. Screw in the new part, and your good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Hubbard, TX
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
would not clean the dishes
I unscrewed the lower spray arm and support assembly and then screwed the new part in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Mt. Pleasant, MI
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tower Broken
Order new part. Lightning fast delivery. Unscrew old one, put in new. 30 seconds. Don't get any easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark L from Dover, DE
- Parts Used:
- WD27X10223
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Panel looked lik an import. Holes did not line up with factory holes.
Held panel in place and drilled holes and installed drill screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Croghan, NY
- Parts Used:
- WD16X10011, WD12X324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Detergent cup cover could not be locked closed prior to washing the dishes.
I removed the plastic inner door liner, removed the timer assembly. Replaced both plastic parts, Detergent cup release arm and dispenser release timer lever. The most difficult part was reassembling the timer lever spring. Long nose pliers made it simple. Works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cliff from knoxville, TN
- Parts Used:
- WD13X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Faulty Dishwasher Door Latch
Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Flintstone, GA
- Parts Used:
- WD13X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door latch would not lock dishwasher door
I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sergei from West Chester, PA
- Parts Used:
- WD08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Replace door gasket
Removed old gasket. Then cleaned the track with a strong paper towel soaked in Windex to remove accumulated scale/soap. Followed the instructions provided with the gasket. I did not need to remove any screws from the door nor did I need to tumble the gasket in a dryer to remove kinks (There really were no kinks in the gasket, as supplied.). I did use a mirror to locate where the gasket should go underneath the bottom of the door, which you can't see. Feeling for the track with your fingers was sufficient for the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Alpharetta, GA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher very noisy when washing/rinsing
Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Town of Tonawanda, NY
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
motor fan broke
I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Mesa, AZ
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking gasket
Removed old gasket, cleaned grooves, installed new gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from mars, PA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Incomplete cleaning / standing water / drain failure
There is sufficient clearance to remove the motor and pump from under the dishwasher after removal of the front lower panels. This avoids the inconvenience of moving the dishwasher. Some ouch work required to remove some of the fittings as sight lines are obstructed - use a mirror to help. Installation is easier as all but one of the hose and pump clamps can be installed with the screw heads accessible from the front. Only installation issue was that the mounting holes on the pump body for the ground wires and the support piece had been drilled but no screw threads had been cut. Two minutes work with a tap solved the problem. One suggestion is to run a couple of loads before replacing the front cover to check for leaks. I did find one after the second load.
Was this instruction helpful to you?
Thank you for voting!