GSD1920C04BB General Electric Dishwasher - Instructions

Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.

Key symptom: when the drain phase begins, there should be a satisfying "Thunk" from the solenoid. No Thunk=solenoid not working

This was really easy. The parts fit perfectly. First i turn off power at circuit panel; turn off water and dissconnected water line and discharge hose. Removed dishwasher from under counter and placed on side. Disconnected connections to motor and pump and replaced and installed same as one unit.

I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!

This repoair was needed due to diswasher leaking out of side door. I just moved in about 6 months ago and needed to use dishwasher. When it leaked i noticed it was in need of a gasket. I searched the internet and came accross "part select". Part showed up in less than 3 days and was a breeze to install. The original gasket came out just by pulling, cleaned up channel and installed new gasket.slid in real easy. I did take off inner door panel to inspect for any damage. none noted. Perfect fit first time. Dont get confused folks if the part has another name as some parts are interchangeable in the industry.

Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.

door gasket dried out due to not using the dishwasher very often and needed to be replaced. removed door, replaced gasket, and re-installed door.

Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...

Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.

Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!

Followed easy instructions and completed repair in less than 30 minutes.

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!

i first order the corner baffles and put them in. no change at all, still leaked terribly. the old baffles looked pretty good so i kept them. i then ordered the door gasket and the insert. i removed the old one, put in the new, and still no change. i thought perhaps the machine hadn't been used at all because it was like brand new inside, and previously owned by 'a little old lady'. i decided to load it up and run it on a regular wash, and have done that three times now. it drips a very small amount on the left corner but i'm quite happy that it decreased so much. I think perhaps the seal might be setting with the heat of the cycle because each time a load goes through it get less and less drips from that corner. The first order was sent by ups and they couldn't find where i lived so i actually had to go pick them up, but the second order was sent fedex and they had no problem finding my home, and i was very pleased with how fast my order came.

Followed the enclosed directions and the video helped a lot. My model needed a different motor mount bar than in the video but wasn't hard to figure out. From shutoff of the water, unplugging, and undoing the screws under the counter and pulling the old pump/motor and installing the new pump/motor and putting it all back took a leisurely 90 minutes. Be sure to hang onto the old plastic covers for the electric leads to reuse.